2019-09-13 11:22:44 +07:00
|
|
|
CFLAGS += \
|
2019-11-20 16:06:40 +07:00
|
|
|
-flto \
|
2019-09-13 11:22:44 +07:00
|
|
|
-mthumb \
|
|
|
|
|
-mabi=aapcs \
|
|
|
|
|
-mcpu=cortex-m4 \
|
|
|
|
|
-mfloat-abi=hard \
|
|
|
|
|
-mfpu=fpv4-sp-d16 \
|
|
|
|
|
-nostdlib -nostartfiles \
|
2019-11-20 16:06:40 +07:00
|
|
|
-DSTM32L476xx \
|
2019-09-13 11:22:44 +07:00
|
|
|
-DCFG_TUSB_MCU=OPT_MCU_STM32L4
|
|
|
|
|
|
2020-10-30 14:01:05 +07:00
|
|
|
# suppress warning caused by vendor mcu driver
|
2020-10-30 14:04:46 +07:00
|
|
|
CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align
|
2020-10-30 14:01:05 +07:00
|
|
|
|
|
|
|
|
ST_FAMILY = l4
|
|
|
|
|
ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
|
|
|
|
|
ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
|
2019-09-13 11:22:44 +07:00
|
|
|
|
|
|
|
|
# All source paths should be relative to the top level.
|
|
|
|
|
LD_FILE = hw/bsp/$(BOARD)/STM32L476VGTx_FLASH.ld
|
|
|
|
|
|
|
|
|
|
SRC_C += \
|
2020-10-30 14:01:05 +07:00
|
|
|
$(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c
|
2019-09-13 11:22:44 +07:00
|
|
|
|
|
|
|
|
SRC_S += \
|
|
|
|
|
$(ST_CMSIS)/Source/Templates/gcc/startup_stm32l476xx.s
|
|
|
|
|
|
|
|
|
|
INC += \
|
2020-10-30 14:14:28 +07:00
|
|
|
$(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
|
2019-09-13 11:22:44 +07:00
|
|
|
$(TOP)/$(ST_CMSIS)/Include \
|
|
|
|
|
$(TOP)/$(ST_HAL_DRIVER)/Inc \
|
|
|
|
|
$(TOP)/hw/bsp/$(BOARD)
|
|
|
|
|
|
|
|
|
|
# For TinyUSB port source
|
|
|
|
|
VENDOR = st
|
|
|
|
|
CHIP_FAMILY = synopsys
|
|
|
|
|
|
|
|
|
|
# For freeRTOS port source
|
|
|
|
|
FREERTOS_PORT = ARM_CM4F
|
|
|
|
|
|
|
|
|
|
# For flash-jlink target
|
|
|
|
|
JLINK_DEVICE = stm32l476vg
|
|
|
|
|
|
|
|
|
|
# Path to STM32 Cube Programmer CLI, should be added into system path
|
|
|
|
|
STM32Prog = STM32_Programmer_CLI
|
|
|
|
|
|
|
|
|
|
# flash target using on-board stlink
|
2021-01-26 12:46:24 +07:00
|
|
|
flash: $(BUILD)/$(PROJECT).elf
|
2019-09-13 11:22:44 +07:00
|
|
|
$(STM32Prog) --connect port=swd --write $< --go
|
