tinyusb/hw/bsp/stm32h743nucleo/board.mk

CFLAGS += \
  -flto \
  -mthumb \
  -mabi=aapcs \
  -mcpu=cortex-m7 \
  -mfloat-abi=hard \
  -mfpu=fpv5-d16 \
  -nostdlib -nostartfiles \
  -DSTM32H743xx \
  -DCFG_TUSB_MCU=OPT_MCU_STM32H7

# suppress warning caused by vendor mcu driver
CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align

ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx

# All source paths should be relative to the top level.
LD_FILE = hw/bsp/$(BOARD)/STM32H743ZITx_FLASH.ld

SRC_C += \
	$(ST_CMSIS)/Source/Templates/system_stm32h7xx.c \
	$(ST_HAL_DRIVER)/Src/stm32h7xx_hal.c \
	$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_cortex.c \
	$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \
	$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \
	$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \
	$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_uart.c \
	$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c

SRC_S += \
	$(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s

INC += \
	$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
	$(TOP)/$(ST_CMSIS)/Include \
	$(TOP)/$(ST_HAL_DRIVER)/Inc \
	$(TOP)/hw/bsp/$(BOARD)

# For TinyUSB port source
VENDOR = st
CHIP_FAMILY = synopsys

# For freeRTOS port source
FREERTOS_PORT = ARM_CM7/r0p1

# flash target using on-board stlink
flash: flash-stlink
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00			`CFLAGS += \`
move -flto to board.mk current board that doesn work with flto is spresense and mimxrt10xx (due to xip image_vector_table is optimized out). 2019-11-20 16:06:40 +07:00			`-flto \`
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00			`-mthumb \`
swith stm32h7 to use st_driver 2019-09-05 23:36:31 +07:00			`-mabi=aapcs \`
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00			`-mcpu=cortex-m7 \`
			`-mfloat-abi=hard \`
			`-mfpu=fpv5-d16 \`
			`-nostdlib -nostartfiles \`
move -flto to board.mk current board that doesn work with flto is spresense and mimxrt10xx (due to xip image_vector_table is optimized out). 2019-11-20 16:06:40 +07:00			`-DSTM32H743xx \`
swith stm32h7 to use st_driver 2019-09-05 23:36:31 +07:00			`-DCFG_TUSB_MCU=OPT_MCU_STM32H7`
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00
stm32h743nucleo: Enable Log via STLINK-VCP. 2020-06-21 17:55:44 +02:00			`# suppress warning caused by vendor mcu driver`
			`CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align`
add -Wextra for more warnings to example non-stack warning (probably mcu driver) should be suppressed in the board.mk 2019-09-27 00:15:43 +07:00
swith stm32h7 to use st_driver 2019-09-05 23:36:31 +07:00			`ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver`
			`ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx`
stm32: Refactor so F4 and H7 use a single Synopsys IP source file. 2019-09-09 10:48:14 -04:00
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00			`# All source paths should be relative to the top level.`
ported stm32f2, added board stm32f207zg nucleo close #127 2019-09-12 10:41:03 +07:00			`LD_FILE = hw/bsp/$(BOARD)/STM32H743ZITx_FLASH.ld`
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00
			`SRC_C += \`
swith stm32h7 to use st_driver 2019-09-05 23:36:31 +07:00			`$(ST_CMSIS)/Source/Templates/system_stm32h7xx.c \`
			`$(ST_HAL_DRIVER)/Src/stm32h7xx_hal.c \`
			`$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_cortex.c \`
			`$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \`
			`$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \`
			`$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \`
stm32h743nucleo: Enable Log via STLINK-VCP. 2020-06-21 17:55:44 +02:00			`$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_uart.c \`
swith stm32h7 to use st_driver 2019-09-05 23:36:31 +07:00			`$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c`
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00
			`SRC_S += \`
swith stm32h7 to use st_driver 2019-09-05 23:36:31 +07:00			`$(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s`
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00
			`INC += \`
swith stm32h7 to use st_driver 2019-09-05 23:36:31 +07:00			`$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \`
			`$(TOP)/$(ST_CMSIS)/Include \`
			`$(TOP)/$(ST_HAL_DRIVER)/Inc \`
			`$(TOP)/hw/bsp/$(BOARD)`
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles. 2019-08-24 12:40:18 -04:00
			`# For TinyUSB port source`
			`VENDOR = st`
stm32: Refactor so F4 and H7 use a single Synopsys IP source file. 2019-09-09 10:48:14 -04:00			`CHIP_FAMILY = synopsys`
tested all the stm32f4 board, work great 2019-09-11 17:37:23 +07:00
fix more build 2020-03-11 00:58:28 +07:00			`# For freeRTOS port source`
			`FREERTOS_PORT = ARM_CM7/r0p1`

tested all the stm32f4 board, work great 2019-09-11 17:37:23 +07:00			`# flash target using on-board stlink`
clean up flash-stlink 2020-01-10 15:09:59 +07:00			`flash: flash-stlink`