tinyusb/hw/bsp/ea4357/board.mk

CFLAGS += \
  -flto \
  -mthumb \
  -mabi=aapcs \
  -mcpu=cortex-m4 \
  -mfloat-abi=hard \
  -mfpu=fpv4-sp-d16 \
  -nostdlib \
  -DCORE_M4 \
  -D__USE_LPCOPEN \
  -DCFG_TUSB_MCU=OPT_MCU_LPC43XX

# mcu driver cause following warnings
CFLAGS += -Wno-error=unused-parameter -Wno-error=strict-prototypes

MCU_DIR = hw/mcu/nxp/lpcopen/lpc43xx/lpc_chip_43xx

# All source paths should be relative to the top level.
LD_FILE = hw/bsp/$(BOARD)/lpc4357.ld

SRC_C += \
	$(MCU_DIR)/../gcc/cr_startup_lpc43xx.c \
	$(MCU_DIR)/src/chip_18xx_43xx.c \
	$(MCU_DIR)/src/clock_18xx_43xx.c \
	$(MCU_DIR)/src/gpio_18xx_43xx.c \
	$(MCU_DIR)/src/sysinit_18xx_43xx.c \
	$(MCU_DIR)/src/i2c_18xx_43xx.c \
	$(MCU_DIR)/src/i2cm_18xx_43xx.c \
	$(MCU_DIR)/src/uart_18xx_43xx.c \
	$(MCU_DIR)/src/fpu_init.c

INC += \
	$(TOP)/$(MCU_DIR)/inc \
	$(TOP)/$(MCU_DIR)/inc/config_43xx

# For TinyUSB port source
VENDOR = nxp
CHIP_FAMILY = transdimension

# For freeRTOS port source
FREERTOS_PORT = ARM_CM4F

# For flash-jlink target
JLINK_DEVICE = LPC4357_M4

# flash using jlink
flash: flash-jlink
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00			`CFLAGS += \`
move -flto to board.mk current board that doesn work with flto is spresense and mimxrt10xx (due to xip image_vector_table is optimized out). 2019-11-20 16:06:40 +07:00			`-flto \`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00			`-mthumb \`
			`-mabi=aapcs \`
			`-mcpu=cortex-m4 \`
revert to use float-abi define __USE_CMSIS instead of __USE_LPCOPEN will have startup enable FPU on startup properly. Although it is only relevant to lpx43/40 series, change all to __USE_CMSIS for consistency 2020-09-02 00:46:08 +07:00			`-mfloat-abi=hard \`
			`-mfpu=fpv4-sp-d16 \`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00			`-nostdlib \`
			`-DCORE_M4 \`
revert to use __USE_LPCOPEN properly init fpu on LPC M4 2020-09-03 12:58:09 +07:00			`-D__USE_LPCOPEN \`
temporarily remove osal_task_delay() from osal - add hcd_uframe_number() API, update EHCI to return uframe number - get host running on ea4357 2020-05-04 14:11:58 +07:00			`-DCFG_TUSB_MCU=OPT_MCU_LPC43XX`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00
add -Wextra for more warnings to example non-stack warning (probably mcu driver) should be suppressed in the board.mk 2019-09-27 00:15:43 +07:00			`# mcu driver cause following warnings`
			`CFLAGS += -Wno-error=unused-parameter -Wno-error=strict-prototypes`
clean up 2019-09-09 12:23:03 +07:00
update makefile for lpc boards 2019-11-11 11:51:51 +07:00			`MCU_DIR = hw/mcu/nxp/lpcopen/lpc43xx/lpc_chip_43xx`
clean up 2019-09-09 12:23:03 +07:00
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00			`# All source paths should be relative to the top level.`
clean up LD_FILE using $(BOARD) make it easier to duplicate bsp 2020-03-07 17:49:30 +07:00			`LD_FILE = hw/bsp/$(BOARD)/lpc4357.ld`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00
			`SRC_C += \`
clean up lpc makefile 2019-09-09 12:39:58 +07:00			`$(MCU_DIR)/../gcc/cr_startup_lpc43xx.c \`
clean up 2019-09-09 12:23:03 +07:00			`$(MCU_DIR)/src/chip_18xx_43xx.c \`
			`$(MCU_DIR)/src/clock_18xx_43xx.c \`
			`$(MCU_DIR)/src/gpio_18xx_43xx.c \`
			`$(MCU_DIR)/src/sysinit_18xx_43xx.c \`
			`$(MCU_DIR)/src/i2c_18xx_43xx.c \`
			`$(MCU_DIR)/src/i2cm_18xx_43xx.c \`
revert to use __USE_LPCOPEN properly init fpu on LPC M4 2020-09-03 12:58:09 +07:00			`$(MCU_DIR)/src/uart_18xx_43xx.c \`
			`$(MCU_DIR)/src/fpu_init.c`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00
			`INC += \`
clean up 2019-09-09 12:23:03 +07:00			`$(TOP)/$(MCU_DIR)/inc \`
			`$(TOP)/$(MCU_DIR)/inc/config_43xx`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00
			`# For TinyUSB port source`
			`VENDOR = nxp`
rename dcd lpc18_43 to transdimension 2019-11-22 14:54:23 +07:00			`CHIP_FAMILY = transdimension`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00
			`# For freeRTOS port source`
freertos demo use static only for most optmized sram 2020-03-11 00:09:37 +07:00			`FREERTOS_PORT = ARM_CM4F`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00
			`# For flash-jlink target`
add more logging to host stack tested host with lpc4357, don't use fpu with lpc m4 since it seems to cause hardfault (stack does not make use of fpu anyway). 2020-09-01 19:16:50 +07:00			`JLINK_DEVICE = LPC4357_M4`
ea4357 build with makefile, add to travis 2019-05-15 18:01:58 +07:00
			`# flash using jlink`
			`flash: flash-jlink`