diff --git a/hw/bsp/stm32u5/boards/stm32u575eval/board.cmake b/hw/bsp/stm32u5/boards/stm32u575eval/board.cmake
index 57ba85c71..dc2f42d94 100644
--- a/hw/bsp/stm32u5/boards/stm32u575eval/board.cmake
+++ b/hw/bsp/stm32u5/boards/stm32u575eval/board.cmake
@@ -1,8 +1,6 @@
set(MCU_VARIANT stm32u575xx)
set(JLINK_DEVICE stm32u575ai)
-set(LD_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/linker/STM32U575xx_FLASH.ld)
-
function(update_board TARGET)
target_compile_definitions(${TARGET} PUBLIC
STM32U575xx
diff --git a/hw/bsp/stm32u5/boards/stm32u575nucleo/board.cmake b/hw/bsp/stm32u5/boards/stm32u575nucleo/board.cmake
index 73bd10033..76285c08f 100644
--- a/hw/bsp/stm32u5/boards/stm32u575nucleo/board.cmake
+++ b/hw/bsp/stm32u5/boards/stm32u575nucleo/board.cmake
@@ -1,8 +1,6 @@
set(MCU_VARIANT stm32u575xx)
set(JLINK_DEVICE stm32u575zi)
-set(LD_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/linker/STM32U575xx_FLASH.ld)
-
function(update_board TARGET)
target_compile_definitions(${TARGET} PUBLIC
STM32U575xx
diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld
index 8aa68a6a6..2d1028cbe 100644
--- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld
+++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld
@@ -35,12 +35,6 @@
/* Entry Point */
ENTRY(Reset_Handler)
-/* Highest address of the user mode stack */
-_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
-
-_Min_Heap_Size = 0x200; /* required amount of heap */
-_Min_Stack_Size = 0x400; /* required amount of stack */
-
/* Memories definition */
MEMORY
{
@@ -49,6 +43,12 @@ MEMORY
FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
}
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
/* Sections */
SECTIONS
{
diff --git a/hw/bsp/stm32u5/family.cmake b/hw/bsp/stm32u5/family.cmake
index cde1df5ca..d3cb78abf 100644
--- a/hw/bsp/stm32u5/family.cmake
+++ b/hw/bsp/stm32u5/family.cmake
@@ -1,9 +1,5 @@
include_guard()
-if (NOT BOARD)
- message(FATAL_ERROR "BOARD not specified")
-endif ()
-
set(ST_FAMILY u5)
set(ST_PREFIX stm32${ST_FAMILY}xx)
@@ -29,7 +25,14 @@ function(add_board_target BOARD_TARGET)
if (NOT TARGET ${BOARD_TARGET})
# Startup & Linker script
set(STARTUP_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/startup_${MCU_VARIANT}.s)
+ set(STARTUP_FILE_Clang ${STARTUP_FILE_GNU})
set(STARTUP_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/startup_${MCU_VARIANT}.s)
+
+ string(REPLACE "stm32u" "STM32U" MCU_VARIANT_UPPER ${MCU_VARIANT})
+ if (NOT DEFINED LD_FILE_GNU)
+ set(LD_FILE_GNU ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/linker/${MCU_VARIANT_UPPER}_FLASH.ld)
+ endif ()
+ set(LD_FILE_Clang ${LD_FILE_GNU})
set(LD_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/linker/${MCU_VARIANT}_flash.icf)
add_library(${BOARD_TARGET} STATIC
@@ -57,9 +60,12 @@ function(add_board_target BOARD_TARGET)
target_link_options(${BOARD_TARGET} PUBLIC
"LINKER:--script=${LD_FILE_GNU}"
-nostartfiles
- # nanolib
--specs=nosys.specs --specs=nano.specs
)
+ elseif (CMAKE_C_COMPILER_ID STREQUAL "Clang")
+ target_link_options(${BOARD_TARGET} PUBLIC
+ "LINKER:--script=${LD_FILE_Clang}"
+ )
elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR")
target_link_options(${BOARD_TARGET} PUBLIC
"LINKER:--config=${LD_FILE_IAR}"
diff --git a/hw/bsp/stm32u5/linker/STM32U535xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U535xx_FLASH.ld
new file mode 100644
index 000000000..6ac1479a3
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U535xx_FLASH.ld
@@ -0,0 +1,167 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U535xE Device from STM32U5 series
+** 512Kbytes FLASH
+** 272Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** Copyright (c) 2022 STMicroelectronics.
+** All rights reserved.
+**
+** This software is licensed under terms that can be found in the LICENSE file
+** in the root directory of this software component.
+** If no LICENSE file comes with this software, it is provided AS-IS.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 256K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 512K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U545xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U545xx_FLASH.ld
new file mode 100644
index 000000000..ce370c643
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U545xx_FLASH.ld
@@ -0,0 +1,167 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U545xE Device from STM32U5 series
+** 512Kbytes FLASH
+** 272Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** Copyright (c) 2022 STMicroelectronics.
+** All rights reserved.
+**
+** This software is licensed under terms that can be found in the LICENSE file
+** in the root directory of this software component.
+** If no LICENSE file comes with this software, it is provided AS-IS.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 256K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 512K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U575xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U575xx_FLASH.ld
new file mode 100644
index 000000000..b24c533de
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U575xx_FLASH.ld
@@ -0,0 +1,185 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : Auto-generated by STM32CubeIDE
+**
+** Abstract : Linker script for STM32U575xx Device from STM32U5 series
+** 2048Kbytes ROM
+** 784Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2021 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 768K
+ ROM (rx) : ORIGIN = 0x08000000, LENGTH = 2048K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "ROM" Rom type memory */
+ .isr_vector :
+ {
+ . = ALIGN(8);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(8);
+ } >ROM
+
+ /* The program code and other data into "ROM" Rom type memory */
+ .text :
+ {
+ . = ALIGN(8);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(8);
+ _etext = .; /* define a global symbols at end of code */
+ } >ROM
+
+ /* Constant data into "ROM" Rom type memory */
+ .rodata :
+ {
+ . = ALIGN(8);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(8);
+ } >ROM
+
+ .ARM.extab : {
+ . = ALIGN(8);
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ . = ALIGN(8);
+ } >ROM
+
+ .ARM : {
+ . = ALIGN(8);
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ . = ALIGN(8);
+ } >ROM
+
+ .preinit_array :
+ {
+ . = ALIGN(8);
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ . = ALIGN(8);
+ } >ROM
+
+ .init_array :
+ {
+ . = ALIGN(8);
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ . = ALIGN(8);
+ } >ROM
+
+ .fini_array :
+ {
+ . = ALIGN(8);
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ . = ALIGN(8);
+ } >ROM
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ . = ALIGN(8);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(8);
+ _edata = .; /* define a global symbol at data end */
+
+ } >RAM AT> ROM
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ . = ALIGN(8);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(8);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U585xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U585xx_FLASH.ld
new file mode 100644
index 000000000..15b8054bc
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U585xx_FLASH.ld
@@ -0,0 +1,185 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : Auto-generated by STM32CubeIDE
+**
+** Abstract : Linker script for STM32U585xx Device from STM32U5 series
+** 2048Kbytes ROM
+** 784Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2021 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 768K
+ ROM (rx) : ORIGIN = 0x08000000, LENGTH = 2048K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "ROM" Rom type memory */
+ .isr_vector :
+ {
+ . = ALIGN(8);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(8);
+ } >ROM
+
+ /* The program code and other data into "ROM" Rom type memory */
+ .text :
+ {
+ . = ALIGN(8);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(8);
+ _etext = .; /* define a global symbols at end of code */
+ } >ROM
+
+ /* Constant data into "ROM" Rom type memory */
+ .rodata :
+ {
+ . = ALIGN(8);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(8);
+ } >ROM
+
+ .ARM.extab : {
+ . = ALIGN(8);
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ . = ALIGN(8);
+ } >ROM
+
+ .ARM : {
+ . = ALIGN(8);
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ . = ALIGN(8);
+ } >ROM
+
+ .preinit_array :
+ {
+ . = ALIGN(8);
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ . = ALIGN(8);
+ } >ROM
+
+ .init_array :
+ {
+ . = ALIGN(8);
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ . = ALIGN(8);
+ } >ROM
+
+ .fini_array :
+ {
+ . = ALIGN(8);
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ . = ALIGN(8);
+ } >ROM
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ . = ALIGN(8);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(8);
+ _edata = .; /* define a global symbol at data end */
+
+ } >RAM AT> ROM
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ . = ALIGN(8);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(8);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U595xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U595xx_FLASH.ld
new file mode 100644
index 000000000..100ee14a5
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U595xx_FLASH.ld
@@ -0,0 +1,168 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U595xJ Device from STM32U5 series
+** 4096Kbytes FLASH
+** 2528Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2021 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U599xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U599xx_FLASH.ld
new file mode 100644
index 000000000..55997bf40
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U599xx_FLASH.ld
@@ -0,0 +1,168 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U599xJ Device from STM32U5 series
+** 4096Kbytes FLASH
+** 2528Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2021 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U5A9xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U5A9xx_FLASH.ld
new file mode 100644
index 000000000..a5f7d3405
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U5A9xx_FLASH.ld
@@ -0,0 +1,168 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U5A9xJ Device from STM32U5 series
+** 4096Kbytes FLASH
+** 2528Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2021 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U5F7xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U5F7xx_FLASH.ld
new file mode 100644
index 000000000..bb9953440
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U5F7xx_FLASH.ld
@@ -0,0 +1,168 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U5F7xJ Device from STM32U5 series
+** 4096Kbytes FLASH
+** 2528Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2023 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U5F9xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U5F9xx_FLASH.ld
new file mode 100644
index 000000000..d8f1f4c5f
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U5F9xx_FLASH.ld
@@ -0,0 +1,168 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U5F9xJ Device from STM32U5 series
+** 4096Kbytes FLASH
+** 2528Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2023 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U5G7xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U5G7xx_FLASH.ld
new file mode 100644
index 000000000..d02d6ebf1
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U5G7xx_FLASH.ld
@@ -0,0 +1,168 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U5G7xJ Device from STM32U5 series
+** 4096Kbytes FLASH
+** 2528Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2023 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32u5/linker/STM32U5G9xx_FLASH.ld b/hw/bsp/stm32u5/linker/STM32U5G9xx_FLASH.ld
new file mode 100644
index 000000000..1b072fdd4
--- /dev/null
+++ b/hw/bsp/stm32u5/linker/STM32U5G9xx_FLASH.ld
@@ -0,0 +1,168 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32U5G9xJ Device from STM32U5 series
+** 4096Kbytes FLASH
+** 2528Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © Copyright (c) 2023 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K
+ SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ KEEP(*(.isr_vector)) /* Startup code */
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ } >FLASH
+
+ .ARM.extab :
+ {
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ } >FLASH
+
+ .ARM :
+ {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/tools/get_deps.py b/tools/get_deps.py
index 70c161132..bf6ef8c00 100644
--- a/tools/get_deps.py
+++ b/tools/get_deps.py
@@ -111,7 +111,7 @@ deps_optional = {
'd922865fc0326a102c26211c44b8e42f52c1e53d',
'stm32l5'],
'hw/mcu/st/cmsis_device_u5': ['https://github.com/STMicroelectronics/cmsis_device_u5.git',
- '06d7edade7167b0eafdd550bf77cfc4fa98eae2e',
+ '5ad9797c54ec3e55eff770fc9b3cd4a1aefc1309',
'stm32u5'],
'hw/mcu/st/cmsis_device_wb': ['https://github.com/STMicroelectronics/cmsis_device_wb.git',
'9c5d1920dd9fabbe2548e10561d63db829bb744f',