adding keil mcb4300 support

- implement board_leds & board_uart routines

demos/bsp/boards/board.h

@@ -59,11 +59,19 @@
 #include <stdint.h>
 #include "tusb.h"
 
+//--------------------------------------------------------------------+
+// BOARD DEFINE
+//--------------------------------------------------------------------+
 #define BOARD_AT86RF2XX             1
 #define BOARD_LPCXPRESSO1347        2
+
 #define BOARD_NGX4330               3
 #define BOARD_EA4357                4
+#define BOARD_MCB4300               5
 
+//--------------------------------------------------------------------+
+// PRINTF TARGET DEFINE
+//--------------------------------------------------------------------+
 #define PRINTF_TARGET_DEBUG_CONSOLE 1 // IDE semihosting console
 #define PRINTF_TARGET_UART          2
 #define PRINTF_TARGET_SWO           3 // aka SWV, ITM
@@ -81,6 +89,8 @@
   #include "board_at86rf2xx.h"
 #elif BOARD == BOARD_EA4357
   #include "embedded_artists/board_ea4357.h"
+#elif BOARD == BOARD_MCB4300
+  #include "keil/board_mcb4300.h"
 #else
   #error BOARD is not defined or supported yet
 #endif

demos/bsp/boards/embedded_artists/board_ea4357.c

@@ -40,15 +40,16 @@
 
 #if BOARD == BOARD_EA4357
 
-#include "common/assertion.h" // TODO there is hal_debugger_ in assertion
 
-#define UART_PORT   LPC_USART0
+#define BOARD_UART_PORT           LPC_USART0
+#define BOARD_UART_PIN_PORT 0x0f
+#define BOARD_UART_PIN_TX   10 // PF.10 : UART0_TXD
+#define BOARD_UART_PIN_RX   11 // PF.11 : UART0_RXD
 
 void board_init(void)
 {
   SystemInit();
   CGU_Init();
-
   SysTick_Config(CGU_GetPCLKFrequency(CGU_PERIPHERAL_M4CORE) / CFG_TICKS_PER_SECOND); // 1 msec tick timer
 
   // USB0 Power: EA4357 channel B U20 GPIO26 active low (base board), P2_3 on LPC4357
@@ -68,16 +69,16 @@ void board_init(void)
 
 #if CFG_UART_ENABLE
   //------------- UART init -------------//
-	scu_pinmux(0xF ,10 , MD_PDN, FUNC1); 	              // PF.10 : UART0_TXD
-	scu_pinmux(0xF ,11 , MD_PLN|MD_EZI|MD_ZI, FUNC1); 	// PF.11 : UART0_RXD
+	scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_TX, MD_PDN             , FUNC1);
+	scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_RX, MD_PLN|MD_EZI|MD_ZI, FUNC1);
 
 	UART_CFG_Type UARTConfigStruct;
   UART_ConfigStructInit(&UARTConfigStruct);
 	UARTConfigStruct.Baud_rate = CFG_UART_BAUDRATE;
 	UARTConfigStruct.Clock_Speed = 0;
 
-	UART_Init(UART_PORT, &UARTConfigStruct);
-	UART_TxCmd(UART_PORT, ENABLE); // Enable UART Transmit
+	UART_Init(BOARD_UART_PORT, &UARTConfigStruct);
+	UART_TxCmd(BOARD_UART_PORT, ENABLE); // Enable UART Transmit
 #endif
 
 #if CFG_PRINTF_TARGET == PRINTF_TARGET_SWO
@@ -98,12 +99,12 @@ void board_leds(uint32_t on_mask, uint32_t off_mask)
 #if CFG_UART_ENABLE
 uint32_t board_uart_send(uint8_t *buffer, uint32_t length)
 {
-  return UART_Send(UART_PORT, buffer, length, BLOCKING);
+  return UART_Send(BOARD_UART_PORT, buffer, length, BLOCKING);
 }
 
 uint32_t board_uart_recv(uint8_t *buffer, uint32_t length)
 {
-  return UART_Receive(UART_PORT, buffer, length, BLOCKING);
+  return UART_Receive(BOARD_UART_PORT, buffer, length, BLOCKING);
 }
 #endif
 

demos/bsp/boards/embedded_artists/board_ea4357.h

@@ -65,10 +65,6 @@
 
 #include "oem_base_board/pca9532.h" // LEDs
 
-#define CFG_LED_NUMBER  0
-#define CFG_LED_ON               (1)
-#define CFG_LED_OFF              (0)
-
 #define CFG_PRINTF_TARGET       PRINTF_TARGET_UART
 
 #ifdef __cplusplus

demos/bsp/boards/keil/board_mcb4300.c

@@ -0,0 +1,144 @@
+/**************************************************************************/
+/*!
+    @file     board_mcb4300.c
+    @author   hathach (tinyusb.org)
+
+    @section LICENSE
+
+    Software License Agreement (BSD License)
+
+    Copyright (c) 2013, hathach (tinyusb.org)
+    All rights reserved.
+
+    Redistribution and use in source and binary forms, with or without
+    modification, are permitted provided that the following conditions are met:
+    1. Redistributions of source code must retain the above copyright
+    notice, this list of conditions and the following disclaimer.
+    2. Redistributions in binary form must reproduce the above copyright
+    notice, this list of conditions and the following disclaimer in the
+    documentation and/or other materials provided with the distribution.
+    3. Neither the name of the copyright holders nor the
+    names of its contributors may be used to endorse or promote products
+    derived from this software without specific prior written permission.
+
+    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
+    EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+    WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+    DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
+    DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+    INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+    LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND
+    ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+    INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS
+    SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+    This file is part of the tinyusb stack.
+*/
+/**************************************************************************/
+
+#include "../board.h"
+
+#if BOARD == BOARD_MCB4300
+
+//--------------------------------------------------------------------+
+// INCLUDE
+//--------------------------------------------------------------------+
+#define BOARD_MAX_LEDS      8
+
+#define BOARD_UART_PORT     LPC_USART0
+#define BOARD_UART_PIN_PORT 2
+#define BOARD_UART_PIN_TX   0
+#define BOARD_UART_PIN_RX   1
+
+//--------------------------------------------------------------------+
+// MACRO CONSTANT TYPEDEF
+//--------------------------------------------------------------------+
+static const uint8_t ledports[] = {6, 6, 6, 6, 6, 4, 4, 4};
+static const uint8_t ledbits[] = {24, 25, 26, 27, 28, 12, 13, 14};
+
+const static struct {
+  uint8_t port;
+  uint8_t pin;
+}leds[BOARD_MAX_LEDS] = {
+    {6, 24}, {6, 25}, {6, 26}, {6, 27},
+    {4, 28}, {4, 12}, {4, 13}, {4, 14}};
+
+//--------------------------------------------------------------------+
+// INTERNAL OBJECT & FUNCTION DECLARATION
+//--------------------------------------------------------------------+
+
+//--------------------------------------------------------------------+
+// IMPLEMENTATION
+//--------------------------------------------------------------------+
+void board_init(void)
+{
+  SystemInit();
+  CGU_Init();
+  SysTick_Config(CGU_GetPCLKFrequency(CGU_PERIPHERAL_M4CORE) / CFG_TICKS_PER_SECOND); // 1 msec tick timer
+
+  //------------- USB Bus power HOST ONLY-------------//
+  //scu_pinmux(0x6, 3, MD_PUP | MD_EZI, FUNC1);     		// P6_3 USB0_PWR_EN, USB0 VBus function
+  // Keil VBUS0 on schematic is F1
+
+
+  // TODO USB1 P2_5
+  scu_pinmux(0x2, 5, MD_PLN | MD_EZI | MD_ZI, FUNC2);	// USB1_VBUS monitor presence, must be high for bus reset occur
+  //scu_pinmux(0x9, 5, MD_PUP | MD_EZI, FUNC2);				// P9_5 USB1_PWR_EN, USB1 VBus function
+  // Keil VBUS1 on schematics is P2_5
+
+  //------------- LEDs init, J21 must be installed -------------//
+  for(uint32_t i=0; i<BOARD_MAX_LEDS; i++)
+  {
+    // TODO consider as default pinmux is to GPIO --> no mux
+    GPIO_SetDir(leds[i].port, BIT_(leds[i].pin), 1); // output
+  }
+
+  #if CFG_UART_ENABLE
+  //------------- UART init -------------//
+	scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_TX, MD_PDN             , FUNC1);
+	scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_RX, MD_PLN|MD_EZI|MD_ZI, FUNC1);
+
+	UART_CFG_Type UARTConfigStruct;
+  UART_ConfigStructInit(&UARTConfigStruct);
+	UARTConfigStruct.Baud_rate = CFG_UART_BAUDRATE;
+	UARTConfigStruct.Clock_Speed = 0;
+
+	UART_Init(BOARD_UART_PORT, &UARTConfigStruct);
+	UART_TxCmd(BOARD_UART_PORT, ENABLE); // Enable UART Transmit
+  #endif
+
+}
+
+//--------------------------------------------------------------------+
+// LEDS
+//--------------------------------------------------------------------+
+void board_leds(uint32_t on_mask, uint32_t off_mask)
+{
+  for (uint32_t i=0; i<BOARD_MAX_LEDS; i++)
+  {
+    if ( on_mask & BIT_(i))
+    {
+      GPIO_SetValue(leds[i].port, BIT_(leds[i].pin));
+    }else if ( off_mask & BIT_(i)) // on_mask take precedence over off_mask
+    {
+      GPIO_ClearValue(leds[i].port, BIT_(leds[i].pin));
+    }
+  }
+}
+
+//--------------------------------------------------------------------+
+// UART
+//--------------------------------------------------------------------+
+#if CFG_UART_ENABLE
+uint32_t board_uart_send(uint8_t *buffer, uint32_t length)
+{
+  return UART_Send(BOARD_UART_PORT, buffer, length, BLOCKING);
+}
+
+uint32_t board_uart_recv(uint8_t *buffer, uint32_t length)
+{
+  return UART_Receive(BOARD_UART_PORT, buffer, length, BLOCKING);
+}
+#endif
+
+#endif

demos/bsp/boards/keil/board_mcb4300.h

@@ -0,0 +1,68 @@
+/**************************************************************************/
+/*!
+    @file     board_mcb4300.h
+    @author   hathach (tinyusb.org)
+
+    @section LICENSE
+
+    Software License Agreement (BSD License)
+
+    Copyright (c) 2013, hathach (tinyusb.org)
+    All rights reserved.
+
+    Redistribution and use in source and binary forms, with or without
+    modification, are permitted provided that the following conditions are met:
+    1. Redistributions of source code must retain the above copyright
+    notice, this list of conditions and the following disclaimer.
+    2. Redistributions in binary form must reproduce the above copyright
+    notice, this list of conditions and the following disclaimer in the
+    documentation and/or other materials provided with the distribution.
+    3. Neither the name of the copyright holders nor the
+    names of its contributors may be used to endorse or promote products
+    derived from this software without specific prior written permission.
+
+    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
+    EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+    WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+    DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
+    DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+    (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+    LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+    ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+    (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+    SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+    This file is part of the tinyusb stack.
+*/
+/**************************************************************************/
+
+/** \ingroup TBD
+ *  \defgroup TBD
+ *  \brief TBD
+ *
+ *  @{
+ */
+
+#ifndef _TUSB_BOARD_MCB4300_H_
+#define _TUSB_BOARD_MCB4300_H_
+
+#include "LPC43xx.h"
+#include "lpc43xx_scu.h"
+#include "lpc43xx_cgu.h"
+#include "lpc43xx_gpio.h"
+#include "lpc43xx_uart.h"
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define CFG_PRINTF_TARGET       PRINTF_TARGET_UART
+
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* _TUSB_BOARD_MCB4300_H_ */
+
+/** @} */

demos/bsp/boards/ngx/board_ngx4330.c

@@ -40,16 +40,6 @@
 
 #if BOARD == BOARD_NGX4330
 
-#include "lpc43xx_uart.h"
-#include "lpc43xx_scu.h"
-#include "lpc43xx_cgu.h"
-#include "lpc43xx_gpio.h"
-#include "lpc43xx_timer.h"
-#include "lpc43xx_i2c.h"
-#include "lpc43xx_gpdma.h"
-#include "lpc43xx_i2s.h"
-#include "lpc43xx_emc.h"
-
 #define BOARD_MAX_LEDS  2
 const static struct {
   uint8_t port;
@@ -93,17 +83,26 @@ void board_init(void)
 
 }
 
-void board_leds(uint32_t mask, uint32_t state)
+//--------------------------------------------------------------------+
+// LEDS
+//--------------------------------------------------------------------+
+void board_leds(uint32_t on_mask, uint32_t off_mask)
 {
-  for(uint8_t i=0; i<BOARD_MAX_LEDS; i++)
+  for (uint32_t i=0; i<BOARD_MAX_LEDS; i++)
   {
-    if ( mask & BIT_(i) )
+    if ( on_mask & BIT_(i))
     {
-      (mask & state) ? GPIO_SetValue(leds[i].port, BIT_(leds[i].pin)) : GPIO_ClearValue(leds[i].port, BIT_(leds[i].pin)) ;
+      GPIO_SetValue(leds[i].port, BIT_(leds[i].pin));
+    }else if ( off_mask & BIT_(i)) // on_mask take precedence over off_mask
+    {
+      GPIO_ClearValue(leds[i].port, BIT_(leds[i].pin));
     }
   }
 }
 
+//--------------------------------------------------------------------+
+// UART
+//--------------------------------------------------------------------+
 uint32_t board_uart_send(uint8_t *p_buffer, uint32_t length)
 {
   return UART_Send((LPC_USARTn_Type*) LPC_USART0, p_buffer, length, BLOCKING);

demos/bsp/boards/ngx/board_ngx4330.h

@@ -52,19 +52,15 @@
 #ifndef _TUSB_BOARD_NGX4330_H_
 #define _TUSB_BOARD_NGX4330_H_
 
-#ifdef __cplusplus
- extern "C" {
-#endif
-
 #include "LPC43xx.h"
 #include "lpc43xx_scu.h"
 #include "lpc43xx_cgu.h"
 #include "lpc43xx_gpio.h"
 #include "lpc43xx_uart.h"
 
-#define CFG_LED_NUMBER  0
-#define CFG_LED_ON               (1)
-#define CFG_LED_OFF              (0)
+#ifdef __cplusplus
+ extern "C" {
+#endif
 
 #define CFG_PRINTF_TARGET       PRINTF_TARGET_DEBUG_CONSOLE