mirror of
https://github.com/hathach/tinyusb.git
synced 2025-01-17 05:32:55 +08:00
refactor stm32f407 to use st hal api
This commit is contained in:
hathach
parent
cb8a33ca87
commit
be4eeeb943
@ -13,14 +13,20 @@ CFLAGS += \
|
||||
LD_FILE = hw/bsp/stm32f407disco/STM32F407VGTx_FLASH.ld
|
||||
|
||||
SRC_C += \
|
||||
hw/mcu/st/system-init/system_stm32f4xx.c
|
||||
hw/mcu/st/system-init/system_stm32f4xx.c \
|
||||
hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c \
|
||||
hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c \
|
||||
hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c \
|
||||
hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c
|
||||
|
||||
SRC_S += \
|
||||
hw/mcu/st/startup/stm32f4/startup_stm32f407xx.s
|
||||
|
||||
INC += \
|
||||
$(TOP)/hw/mcu/st/cmsis \
|
||||
$(TOP)/hw/mcu/st/stm32lib/CMSIS/STM32F4xx/Include \
|
||||
$(TOP)/hw/mcu/st/cmsis
|
||||
$(TOP)/hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Inc \
|
||||
$(TOP)/hw/bsp/stm32f407disco
|
||||
|
||||
# For TinyUSB port source
|
||||
VENDOR = st
|
||||
|
||||
@ -27,39 +27,13 @@
|
||||
#include "../board.h"
|
||||
|
||||
#include "stm32f4xx.h"
|
||||
#include "stm32f4xx_hal_conf.h"
|
||||
|
||||
#define LED_PORT GPIOD
|
||||
#define LED_PIN GPIO_PIN_14
|
||||
|
||||
void board_init(void)
|
||||
{
|
||||
// Init the LED on PD14
|
||||
RCC->AHB1ENR |= RCC_AHB1ENR_GPIODEN;
|
||||
GPIOD->MODER |= GPIO_MODER_MODE14_0;
|
||||
|
||||
// TODO Button
|
||||
|
||||
// USB Clock init
|
||||
// PLL input- 8 MHz (External oscillator clock; HSI clock tolerance isn't
|
||||
// tight enough- 1%, need 0.25%)
|
||||
// VCO input- 1 to 2 MHz (2 MHz, M = 4)
|
||||
// VCO output- 100 to 432 MHz (144 MHz, N = 72)
|
||||
// Main PLL out- <= 180 MHz (18 MHz, P = 3- divides by 8)
|
||||
// USB PLL out- 48 MHz (Q = 3)
|
||||
RCC->PLLCFGR = RCC_PLLCFGR_PLLSRC_HSE | (3 << RCC_PLLCFGR_PLLQ_Pos) | \
|
||||
(3 << RCC_PLLCFGR_PLLP_Pos) | (72 << RCC_PLLCFGR_PLLN_Pos) | \
|
||||
(4 << RCC_PLLCFGR_PLLM_Pos);
|
||||
|
||||
// Wait for external clock to become ready
|
||||
RCC->CR |= RCC_CR_HSEON;
|
||||
while(!(RCC->CR & RCC_CR_HSERDY_Msk));
|
||||
|
||||
// Wait for PLL to become ready
|
||||
RCC->CR |= RCC_CR_PLLON;
|
||||
while(!(RCC->CR & RCC_CR_PLLRDY_Msk));
|
||||
|
||||
// Switch clocks!
|
||||
RCC->CFGR |= RCC_CFGR_SW_1;
|
||||
|
||||
// Notify runtime of frequency change.
|
||||
SystemCoreClockUpdate();
|
||||
|
||||
#if CFG_TUSB_OS == OPT_OS_NONE
|
||||
// 1ms tick timer
|
||||
@ -69,21 +43,100 @@ void board_init(void)
|
||||
//NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
|
||||
#endif
|
||||
|
||||
RCC->AHB2ENR |= RCC_AHB2ENR_OTGFSEN;
|
||||
/** System Clock Configuration
|
||||
* The system Clock is configured as follow :
|
||||
* System Clock source = PLL (HSE)
|
||||
* SYSCLK(Hz) = 168000000
|
||||
* HCLK(Hz) = 168000000
|
||||
* AHB Prescaler = 1
|
||||
* APB1 Prescaler = 4
|
||||
* APB2 Prescaler = 2
|
||||
* HSE Frequency(Hz) = 8000000
|
||||
* PLL_M = 8
|
||||
* PLL_N = 336
|
||||
* PLL_P = 2
|
||||
* PLL_Q = 7
|
||||
* VDD(V) = 3.3
|
||||
* Main regulator output voltage = Scale1 mode
|
||||
* Flash Latency(WS) = 5
|
||||
*/
|
||||
RCC_ClkInitTypeDef RCC_ClkInitStruct;
|
||||
RCC_OscInitTypeDef RCC_OscInitStruct;
|
||||
|
||||
/* Enable Power Control clock */
|
||||
__HAL_RCC_PWR_CLK_ENABLE();
|
||||
|
||||
/* The voltage scaling allows optimizing the power consumption when the device is
|
||||
clocked below the maximum system frequency, to update the voltage scaling value
|
||||
regarding system frequency refer to product datasheet. */
|
||||
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
|
||||
|
||||
/* Enable HSE Oscillator and activate PLL with HSE as source */
|
||||
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
|
||||
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
|
||||
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
|
||||
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
|
||||
RCC_OscInitStruct.PLL.PLLM = 8;
|
||||
RCC_OscInitStruct.PLL.PLLN = 336;
|
||||
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
|
||||
RCC_OscInitStruct.PLL.PLLQ = 7;
|
||||
HAL_RCC_OscConfig(&RCC_OscInitStruct);
|
||||
|
||||
/* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
|
||||
clocks dividers */
|
||||
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
|
||||
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
|
||||
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
||||
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
|
||||
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
|
||||
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
|
||||
|
||||
// Notify runtime of frequency change.
|
||||
SystemCoreClockUpdate();
|
||||
|
||||
// Enable USB OTG clock
|
||||
__HAL_RCC_USB_OTG_FS_CLK_ENABLE();
|
||||
|
||||
GPIO_InitTypeDef GPIO_InitStruct;
|
||||
|
||||
// USB Pin Init
|
||||
// PA9- VUSB, PA10- ID, PA11- DM, PA12- DP
|
||||
// PC0- Power on
|
||||
RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN;
|
||||
GPIOA->MODER |= GPIO_MODER_MODE9_1 | GPIO_MODER_MODE10_1 | \
|
||||
GPIO_MODER_MODE11_1 | GPIO_MODER_MODE12_1;
|
||||
GPIOA->AFR[1] |= (10 << GPIO_AFRH_AFSEL9_Pos) | \
|
||||
(10 << GPIO_AFRH_AFSEL10_Pos) | (10 << GPIO_AFRH_AFSEL11_Pos) | \
|
||||
(10 << GPIO_AFRH_AFSEL12_Pos);
|
||||
__HAL_RCC_GPIOA_CLK_ENABLE();
|
||||
|
||||
// Pullup required on ID, despite the manual claiming there's an
|
||||
// internal pullup already (page 1245, Rev 17)
|
||||
GPIOA->PUPDR |= GPIO_PUPDR_PUPD10_0;
|
||||
/* Configure DM DP Pins */
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
|
||||
/* Configure VBUS Pin */
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_9;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
|
||||
/* This for ID line debug */
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_10;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
|
||||
// Init the LED
|
||||
__HAL_RCC_GPIOD_CLK_ENABLE();
|
||||
|
||||
GPIO_InitStruct.Pin = LED_PIN;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
|
||||
HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
|
||||
|
||||
board_led_write(false);
|
||||
|
||||
// TODO Button
|
||||
}
|
||||
|
||||
//--------------------------------------------------------------------+
|
||||
@ -92,11 +145,7 @@ void board_init(void)
|
||||
|
||||
void board_led_write(bool state)
|
||||
{
|
||||
if (!state) {
|
||||
GPIOD->BSRR = GPIO_BSRR_BR14;
|
||||
} else {
|
||||
GPIOD->BSRR = GPIO_BSRR_BS14;
|
||||
}
|
||||
HAL_GPIO_WritePin(LED_PORT, LED_PIN, state);
|
||||
}
|
||||
|
||||
uint32_t board_button_read(void)
|
||||
|
||||
@ -23,10 +23,10 @@ SRC_S += \
|
||||
hw/mcu/st/startup/stm32f4/startup_stm32f411xe.s
|
||||
|
||||
INC += \
|
||||
$(TOP)/hw/bsp/stm32f411disco \
|
||||
$(TOP)/hw/mcu/st/cmsis \
|
||||
$(TOP)/hw/mcu/st/stm32lib/CMSIS/STM32F4xx/Include \
|
||||
$(TOP)/hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Inc \
|
||||
$(TOP)/hw/mcu/st/cmsis
|
||||
$(TOP)/hw/bsp/stm32f411disco
|
||||
|
||||
# For TinyUSB port source
|
||||
VENDOR = st
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user