mirror of
https://github.com/hathach/tinyusb.git
synced 2025-01-17 05:32:55 +08:00
hathach
parent
3a17ae8714
commit
ff7261600c
@ -55,7 +55,7 @@ The stack supports the following MCUs
|
||||
- **Nordic:** nRF52840
|
||||
- **NXP:** LPC11Uxx, LPC13xx, LPC175x_6x, LPC177x_8x, LPC18xx, LPC40xx, LPC43xx, LPC51Uxx
|
||||
- **MicroChip:** SAMD21, SAMD51 (device only)
|
||||
- **ST:** STM32F0, STM32F3, STM32F4, STM32F7, STM32H7 (device only)
|
||||
- **ST:** STM32F0, STM32F2, STM32F3, STM32F4, STM32F7, STM32H7 (device only)
|
||||
|
||||
[Here is the list of supported Boards](docs/boards.md)
|
||||
|
||||
|
||||
@ -43,6 +43,7 @@ This code base already had supported for a handful of following boards
|
||||
|
||||
- [STM32F070rb Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f070rb.html)
|
||||
- [STM32F072rb Discovery](https://www.st.com/en/evaluation-tools/32f072bdiscovery.html)
|
||||
- [STM32F207zg Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f207zg.html)
|
||||
- [STM32F303vc Discovery](https://www.st.com/en/evaluation-tools/stm32f3discovery.html)
|
||||
- [STM32F407vg Discovery](https://www.st.com/en/evaluation-tools/stm32f4discovery.html)
|
||||
- [STM32F411ve Discovery](https://www.st.com/en/evaluation-tools/32f411ediscovery.html)
|
||||
|
||||
@ -13,7 +13,7 @@ ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F0xx_HAL_Driver
|
||||
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F0xx
|
||||
|
||||
# All source paths should be relative to the top level.
|
||||
LD_FILE = hw/bsp/stm32f070rbnucleo/stm32F070rbtx_flash.ld
|
||||
LD_FILE = hw/bsp/$(BOARD)/stm32F070rbtx_flash.ld
|
||||
|
||||
SRC_C += \
|
||||
$(ST_CMSIS)/Source/Templates/system_stm32f0xx.c \
|
||||
|
||||
169
hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld
Normal file
169
hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld
Normal file
@ -0,0 +1,169 @@
|
||||
/*
|
||||
*****************************************************************************
|
||||
**
|
||||
|
||||
** File : LinkerScript.ld
|
||||
**
|
||||
** Abstract : Linker script for STM32F207IGHx Device with
|
||||
** 1024KByte FLASH, 128KByte RAM
|
||||
**
|
||||
** Set heap size, stack size and stack location according
|
||||
** to application requirements.
|
||||
**
|
||||
** Set memory bank area and size if external memory is used.
|
||||
**
|
||||
** Target : STMicroelectronics STM32
|
||||
**
|
||||
**
|
||||
** Distribution: The file is distributed as is, without any warranty
|
||||
** of any kind.
|
||||
**
|
||||
** (c)Copyright Ac6.
|
||||
** You may use this file as-is or modify it according to the needs of your
|
||||
** project. Distribution of this file (unmodified or modified) is not
|
||||
** permitted. Ac6 permit registered System Workbench for MCU users the
|
||||
** rights to distribute the assembled, compiled & linked contents of this
|
||||
** file as part of an application binary file, provided that it is built
|
||||
** using the System Workbench for MCU toolchain.
|
||||
**
|
||||
*****************************************************************************
|
||||
*/
|
||||
|
||||
/* Entry Point */
|
||||
ENTRY(Reset_Handler)
|
||||
|
||||
/* Highest address of the user mode stack */
|
||||
_estack = 0x20020000; /* end of RAM */
|
||||
/* Generate a link error if heap and stack don't fit into RAM */
|
||||
_Min_Heap_Size = 0x200; /* required amount of heap */
|
||||
_Min_Stack_Size = 0x400; /* required amount of stack */
|
||||
|
||||
/* Specify the memory areas */
|
||||
MEMORY
|
||||
{
|
||||
FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 1024K
|
||||
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K
|
||||
}
|
||||
|
||||
/* Define output sections */
|
||||
SECTIONS
|
||||
{
|
||||
/* The startup code goes first into FLASH */
|
||||
.isr_vector :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
KEEP(*(.isr_vector)) /* Startup code */
|
||||
. = ALIGN(4);
|
||||
} >FLASH
|
||||
|
||||
/* The program code and other data goes into FLASH */
|
||||
.text :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
*(.text) /* .text sections (code) */
|
||||
*(.text*) /* .text* sections (code) */
|
||||
*(.glue_7) /* glue arm to thumb code */
|
||||
*(.glue_7t) /* glue thumb to arm code */
|
||||
*(.eh_frame)
|
||||
|
||||
KEEP (*(.init))
|
||||
KEEP (*(.fini))
|
||||
|
||||
. = ALIGN(4);
|
||||
_etext = .; /* define a global symbols at end of code */
|
||||
} >FLASH
|
||||
|
||||
/* Constant data goes into FLASH */
|
||||
.rodata :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
*(.rodata) /* .rodata sections (constants, strings, etc.) */
|
||||
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */
|
||||
. = ALIGN(4);
|
||||
} >FLASH
|
||||
|
||||
.ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
|
||||
.ARM : {
|
||||
__exidx_start = .;
|
||||
*(.ARM.exidx*)
|
||||
__exidx_end = .;
|
||||
} >FLASH
|
||||
|
||||
.preinit_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__preinit_array_start = .);
|
||||
KEEP (*(.preinit_array*))
|
||||
PROVIDE_HIDDEN (__preinit_array_end = .);
|
||||
} >FLASH
|
||||
.init_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__init_array_start = .);
|
||||
KEEP (*(SORT(.init_array.*)))
|
||||
KEEP (*(.init_array*))
|
||||
PROVIDE_HIDDEN (__init_array_end = .);
|
||||
} >FLASH
|
||||
.fini_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__fini_array_start = .);
|
||||
KEEP (*(SORT(.fini_array.*)))
|
||||
KEEP (*(.fini_array*))
|
||||
PROVIDE_HIDDEN (__fini_array_end = .);
|
||||
} >FLASH
|
||||
|
||||
/* used by the startup to initialize data */
|
||||
_sidata = LOADADDR(.data);
|
||||
|
||||
/* Initialized data sections goes into RAM, load LMA copy after code */
|
||||
.data :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
_sdata = .; /* create a global symbol at data start */
|
||||
*(.data) /* .data sections */
|
||||
*(.data*) /* .data* sections */
|
||||
|
||||
. = ALIGN(4);
|
||||
_edata = .; /* define a global symbol at data end */
|
||||
} >RAM AT> FLASH
|
||||
|
||||
|
||||
/* Uninitialized data section */
|
||||
. = ALIGN(4);
|
||||
.bss :
|
||||
{
|
||||
/* This is used by the startup in order to initialize the .bss secion */
|
||||
_sbss = .; /* define a global symbol at bss start */
|
||||
__bss_start__ = _sbss;
|
||||
*(.bss)
|
||||
*(.bss*)
|
||||
*(COMMON)
|
||||
|
||||
. = ALIGN(4);
|
||||
_ebss = .; /* define a global symbol at bss end */
|
||||
__bss_end__ = _ebss;
|
||||
} >RAM
|
||||
|
||||
/* User_heap_stack section, used to check that there is enough RAM left */
|
||||
._user_heap_stack :
|
||||
{
|
||||
. = ALIGN(8);
|
||||
PROVIDE ( end = . );
|
||||
PROVIDE ( _end = . );
|
||||
. = . + _Min_Heap_Size;
|
||||
. = . + _Min_Stack_Size;
|
||||
. = ALIGN(8);
|
||||
} >RAM
|
||||
|
||||
|
||||
|
||||
/* Remove information from the standard libraries */
|
||||
/DISCARD/ :
|
||||
{
|
||||
libc.a ( * )
|
||||
libm.a ( * )
|
||||
libgcc.a ( * )
|
||||
}
|
||||
|
||||
.ARM.attributes 0 : { *(.ARM.attributes) }
|
||||
}
|
||||
|
||||
|
||||
53
hw/bsp/stm32f207nucleo/board.mk
Normal file
53
hw/bsp/stm32f207nucleo/board.mk
Normal file
@ -0,0 +1,53 @@
|
||||
CFLAGS += \
|
||||
-DHSE_VALUE=8000000 \
|
||||
-DSTM32F207xx \
|
||||
-mthumb \
|
||||
-mabi=aapcs \
|
||||
-mcpu=cortex-m3 \
|
||||
-mfloat-abi=soft \
|
||||
-nostdlib -nostartfiles \
|
||||
-DCFG_TUSB_MCU=OPT_MCU_STM32F2
|
||||
|
||||
# Suppress following warnings/error is required due to STM32F2xx_HAL_Driver.
|
||||
CFLAGS += -Wno-error=sign-compare
|
||||
|
||||
ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F2xx_HAL_Driver
|
||||
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F2xx
|
||||
|
||||
# All source paths should be relative to the top level.
|
||||
LD_FILE = hw/bsp/$(BOARD)/STM32F207ZGTx_FLASH.ld
|
||||
|
||||
SRC_C += \
|
||||
$(ST_CMSIS)/Source/Templates/system_stm32f2xx.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f2xx_hal.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f2xx_hal_cortex.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f2xx_hal_rcc.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f2xx_hal_rcc_ex.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f2xx_hal_gpio.c
|
||||
|
||||
SRC_S += \
|
||||
$(ST_CMSIS)/Source/Templates/gcc/startup_stm32f207xx.s
|
||||
|
||||
INC += \
|
||||
$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
|
||||
$(TOP)/$(ST_CMSIS)/Include \
|
||||
$(TOP)/$(ST_HAL_DRIVER)/Inc \
|
||||
$(TOP)/hw/bsp/$(BOARD)
|
||||
|
||||
# For TinyUSB port source
|
||||
VENDOR = st
|
||||
CHIP_FAMILY = synopsys
|
||||
|
||||
# For freeRTOS port source
|
||||
FREERTOS_PORT = ARM_CM3
|
||||
|
||||
# For flash-jlink target
|
||||
JLINK_DEVICE = stm32f207zg
|
||||
JLINK_IF = swd
|
||||
|
||||
# Path to STM32 Cube Programmer CLI, should be added into system path
|
||||
STM32Prog = STM32_Programmer_CLI
|
||||
|
||||
# flash target using on-board stlink
|
||||
flash: $(BUILD)/$(BOARD)-firmware.elf
|
||||
$(STM32Prog) --connect port=swd --write $< --go
|
||||
178
hw/bsp/stm32f207nucleo/stm32f207nucleo.c
Normal file
178
hw/bsp/stm32f207nucleo/stm32f207nucleo.c
Normal file
@ -0,0 +1,178 @@
|
||||
/*
|
||||
* The MIT License (MIT)
|
||||
*
|
||||
* Copyright (c) 2019 Ha Thach (tinyusb.org)
|
||||
*
|
||||
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
||||
* of this software and associated documentation files (the "Software"), to deal
|
||||
* in the Software without restriction, including without limitation the rights
|
||||
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
||||
* copies of the Software, and to permit persons to whom the Software is
|
||||
* furnished to do so, subject to the following conditions:
|
||||
*
|
||||
* The above copyright notice and this permission notice shall be included in
|
||||
* all copies or substantial portions of the Software.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
||||
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
||||
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
||||
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
||||
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
||||
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
||||
* THE SOFTWARE.
|
||||
*
|
||||
* This file is part of the TinyUSB stack.
|
||||
*/
|
||||
|
||||
#include "../board.h"
|
||||
|
||||
#include "stm32f2xx.h"
|
||||
#include "stm32f2xx_hal_conf.h"
|
||||
|
||||
#define LED_PORT GPIOB
|
||||
#define LED_PIN GPIO_PIN_14
|
||||
#define LED_STATE_ON 1
|
||||
|
||||
#define BUTTON_PORT GPIOC
|
||||
#define BUTTON_PIN GPIO_PIN_13
|
||||
#define BUTTON_STATE_ACTIVE 1
|
||||
|
||||
|
||||
/**
|
||||
* @brief System Clock Configuration
|
||||
* The system Clock is configured as follow :
|
||||
* System Clock source = PLL (HSE)
|
||||
* SYSCLK(Hz) = 120000000
|
||||
* HCLK(Hz) = 120000000
|
||||
* AHB Prescaler = 1
|
||||
* APB1 Prescaler = 4
|
||||
* APB2 Prescaler = 2
|
||||
* HSE Frequency(Hz) = 8000000
|
||||
* PLL_M = 8
|
||||
* PLL_N = 240
|
||||
* PLL_P = 2
|
||||
* PLL_Q = 5
|
||||
* VDD(V) = 3.3
|
||||
* Flash Latency(WS) = 3
|
||||
* @param None
|
||||
* @retval None
|
||||
*/
|
||||
void SystemClock_Config(void)
|
||||
{
|
||||
RCC_ClkInitTypeDef RCC_ClkInitStruct;
|
||||
RCC_OscInitTypeDef RCC_OscInitStruct;
|
||||
|
||||
/* Enable HSE Oscillator and activate PLL with HSE as source */
|
||||
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
|
||||
RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
|
||||
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
|
||||
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
|
||||
RCC_OscInitStruct.PLL.PLLM = 8;
|
||||
RCC_OscInitStruct.PLL.PLLN = 240;
|
||||
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
|
||||
RCC_OscInitStruct.PLL.PLLQ = 5;
|
||||
HAL_RCC_OscConfig(&RCC_OscInitStruct);
|
||||
|
||||
/* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
|
||||
clocks dividers */
|
||||
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
|
||||
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
|
||||
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
||||
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
|
||||
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
|
||||
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3);
|
||||
}
|
||||
|
||||
void board_init(void)
|
||||
{
|
||||
#if CFG_TUSB_OS == OPT_OS_NONE
|
||||
// 1ms tick timer
|
||||
SysTick_Config(SystemCoreClock / 1000);
|
||||
#endif
|
||||
|
||||
SystemClock_Config();
|
||||
|
||||
// Notify runtime of frequency change.
|
||||
SystemCoreClockUpdate();
|
||||
|
||||
// LED
|
||||
__HAL_RCC_GPIOB_CLK_ENABLE();
|
||||
GPIO_InitTypeDef GPIO_InitStruct;
|
||||
GPIO_InitStruct.Pin = LED_PIN;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
|
||||
HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
|
||||
|
||||
// Button
|
||||
__HAL_RCC_GPIOC_CLK_ENABLE();
|
||||
GPIO_InitStruct.Pin = BUTTON_PIN;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
|
||||
HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
|
||||
|
||||
/* Configure DM DP Pins */
|
||||
__HAL_RCC_GPIOA_CLK_ENABLE();
|
||||
GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
|
||||
/* Configure VBUS Pin */
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_9;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
|
||||
/* Configure ID pin */
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_10;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
|
||||
/* Enable USB FS Clocks */
|
||||
__HAL_RCC_USB_OTG_FS_CLK_ENABLE();
|
||||
}
|
||||
|
||||
//--------------------------------------------------------------------+
|
||||
// Board porting API
|
||||
//--------------------------------------------------------------------+
|
||||
|
||||
void board_led_write(bool state)
|
||||
{
|
||||
HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
|
||||
}
|
||||
|
||||
uint32_t board_button_read(void)
|
||||
{
|
||||
return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
|
||||
}
|
||||
|
||||
#if CFG_TUSB_OS == OPT_OS_NONE
|
||||
volatile uint32_t system_ticks = 0;
|
||||
void SysTick_Handler (void)
|
||||
{
|
||||
system_ticks++;
|
||||
}
|
||||
|
||||
uint32_t board_millis(void)
|
||||
{
|
||||
return system_ticks;
|
||||
}
|
||||
#endif
|
||||
|
||||
void HardFault_Handler (void)
|
||||
{
|
||||
asm("bkpt");
|
||||
}
|
||||
|
||||
// Required by __libc_init_array in startup code if we are compiling using
|
||||
// -nostdlib/-nostartfiles.
|
||||
void _init(void)
|
||||
{
|
||||
|
||||
}
|
||||
407
hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h
Normal file
407
hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h
Normal file
@ -0,0 +1,407 @@
|
||||
/**
|
||||
******************************************************************************
|
||||
* @file stm32f2xx_hal_conf.h
|
||||
* @author MCD Application Team
|
||||
* @brief HAL configuration file.
|
||||
******************************************************************************
|
||||
* @attention
|
||||
*
|
||||
* <h2><center>© Copyright (c) 2017 STMicroelectronics.
|
||||
* All rights reserved.</center></h2>
|
||||
*
|
||||
* This software component is licensed by ST under BSD 3-Clause license,
|
||||
* the "License"; You may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at:
|
||||
* opensource.org/licenses/BSD-3-Clause
|
||||
*
|
||||
******************************************************************************
|
||||
*/
|
||||
|
||||
/* Define to prevent recursive inclusion -------------------------------------*/
|
||||
#ifndef __STM32F2xx_HAL_CONF_H
|
||||
#define __STM32F2xx_HAL_CONF_H
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
/* Exported types ------------------------------------------------------------*/
|
||||
/* Exported constants --------------------------------------------------------*/
|
||||
|
||||
/* ########################## Module Selection ############################## */
|
||||
/**
|
||||
* @brief This is the list of modules to be used in the HAL driver
|
||||
*/
|
||||
#define HAL_MODULE_ENABLED
|
||||
/* #define HAL_ADC_MODULE_ENABLED */
|
||||
/* #define HAL_CAN_MODULE_ENABLED */
|
||||
/* #define HAL_CRC_MODULE_ENABLED */
|
||||
/* #define HAL_CRYP_MODULE_ENABLED */
|
||||
/* #define HAL_DAC_MODULE_ENABLED */
|
||||
/* #define HAL_DCMI_MODULE_ENABLED */
|
||||
/* #define HAL_DMA_MODULE_ENABLED */
|
||||
/* #define HAL_ETH_MODULE_ENABLED */
|
||||
#define HAL_EXTI_MODULE_ENABLED
|
||||
#define HAL_FLASH_MODULE_ENABLED
|
||||
/* #define HAL_NAND_MODULE_ENABLED */
|
||||
/* #define HAL_NOR_MODULE_ENABLED */
|
||||
/* #define HAL_PCCARD_MODULE_ENABLED */
|
||||
/* #define HAL_SRAM_MODULE_ENABLED */
|
||||
/* #define HAL_HASH_MODULE_ENABLED */
|
||||
#define HAL_GPIO_MODULE_ENABLED
|
||||
/* #define HAL_I2C_MODULE_ENABLED */
|
||||
/* #define HAL_I2S_MODULE_ENABLED */
|
||||
/* #define HAL_IWDG_MODULE_ENABLED */
|
||||
#define HAL_PWR_MODULE_ENABLED
|
||||
#define HAL_RCC_MODULE_ENABLED
|
||||
/* #define HAL_RNG_MODULE_ENABLED */
|
||||
/* #define HAL_RTC_MODULE_ENABLED */
|
||||
/* #define HAL_SD_MODULE_ENABLED */
|
||||
/* #define HAL_SPI_MODULE_ENABLED */
|
||||
/* #define HAL_TIM_MODULE_ENABLED */
|
||||
/* #define HAL_UART_MODULE_ENABLED */
|
||||
/* #define HAL_USART_MODULE_ENABLED */
|
||||
/* #define HAL_IRDA_MODULE_ENABLED */
|
||||
/* #define HAL_SMARTCARD_MODULE_ENABLED */
|
||||
/* #define HAL_WWDG_MODULE_ENABLED */
|
||||
#define HAL_CORTEX_MODULE_ENABLED
|
||||
#define HAL_PCD_MODULE_ENABLED
|
||||
/* #define HAL_HCD_MODULE_ENABLED */
|
||||
|
||||
|
||||
/* ########################## HSE/HSI Values adaptation ##################### */
|
||||
/**
|
||||
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSE is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#if !defined (HSE_VALUE)
|
||||
#define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */
|
||||
#endif /* HSE_VALUE */
|
||||
|
||||
#if !defined (HSE_STARTUP_TIMEOUT)
|
||||
#define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
|
||||
#endif /* HSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief Internal High Speed oscillator (HSI) value.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSI is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#if !defined (HSI_VALUE)
|
||||
#define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/
|
||||
#endif /* HSI_VALUE */
|
||||
|
||||
/**
|
||||
* @brief Internal Low Speed oscillator (LSI) value.
|
||||
*/
|
||||
#if !defined (LSI_VALUE)
|
||||
#define LSI_VALUE 32000U /*!< LSI Typical Value in Hz*/
|
||||
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
|
||||
The real value may vary depending on the variations
|
||||
in voltage and temperature.*/
|
||||
/**
|
||||
* @brief External Low Speed oscillator (LSE) value.
|
||||
*/
|
||||
#if !defined (LSE_VALUE)
|
||||
#define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
|
||||
#endif /* LSE_VALUE */
|
||||
|
||||
#if !defined (LSE_STARTUP_TIMEOUT)
|
||||
#define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
|
||||
#endif /* LSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief External clock source for I2S peripheral
|
||||
* This value is used by the I2S HAL module to compute the I2S clock source
|
||||
* frequency, this source is inserted directly through I2S_CKIN pad.
|
||||
*/
|
||||
#if !defined (EXTERNAL_CLOCK_VALUE)
|
||||
#define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the Internal oscillator in Hz*/
|
||||
#endif /* EXTERNAL_CLOCK_VALUE */
|
||||
|
||||
/* Tip: To avoid modifying this file each time you need to use different HSE,
|
||||
=== you can define the HSE value in your toolchain compiler preprocessor. */
|
||||
|
||||
/* ########################### System Configuration ######################### */
|
||||
/**
|
||||
* @brief This is the HAL system configuration section
|
||||
*/
|
||||
#define VDD_VALUE 3300U /*!< Value of VDD in mv */
|
||||
#define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */
|
||||
#define USE_RTOS 0U
|
||||
#define PREFETCH_ENABLE 1U
|
||||
#define INSTRUCTION_CACHE_ENABLE 1U
|
||||
#define DATA_CACHE_ENABLE 1U
|
||||
|
||||
#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
|
||||
#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
|
||||
#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
|
||||
#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
|
||||
#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
|
||||
#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
|
||||
#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
|
||||
#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
|
||||
#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
|
||||
#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
|
||||
#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
|
||||
#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
|
||||
#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
|
||||
#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
|
||||
#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
|
||||
#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
|
||||
#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
|
||||
#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
|
||||
#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
|
||||
#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
|
||||
#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
|
||||
#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
|
||||
#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
|
||||
#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
|
||||
#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
|
||||
#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
|
||||
|
||||
/* ########################## Assert Selection ############################## */
|
||||
/**
|
||||
* @brief Uncomment the line below to expanse the "assert_param" macro in the
|
||||
* HAL drivers code
|
||||
*/
|
||||
/* #define USE_FULL_ASSERT 1U */
|
||||
|
||||
/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */
|
||||
|
||||
/* Section 1 : Ethernet peripheral configuration */
|
||||
|
||||
/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
|
||||
#define MAC_ADDR0 2U
|
||||
#define MAC_ADDR1 0U
|
||||
#define MAC_ADDR2 0U
|
||||
#define MAC_ADDR3 0U
|
||||
#define MAC_ADDR4 0U
|
||||
#define MAC_ADDR5 0U
|
||||
|
||||
/* Definition of the Ethernet driver buffers size and count */
|
||||
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
|
||||
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
|
||||
#define ETH_RXBUFNB 5U /* 5 Rx buffers of size ETH_RX_BUF_SIZE */
|
||||
#define ETH_TXBUFNB 5U /* 5 Tx buffers of size ETH_TX_BUF_SIZE */
|
||||
|
||||
/* Section 2: PHY configuration section */
|
||||
|
||||
/* LAN8742A PHY Address*/
|
||||
#define LAN8742A_PHY_ADDRESS 0x00U
|
||||
/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
|
||||
#define PHY_RESET_DELAY 0x000000FFU
|
||||
/* PHY Configuration delay */
|
||||
#define PHY_CONFIG_DELAY 0x00000FFFU
|
||||
|
||||
#define PHY_READ_TO 0x0000FFFFU
|
||||
#define PHY_WRITE_TO 0x0000FFFFU
|
||||
|
||||
/* Section 3: Common PHY Registers */
|
||||
|
||||
#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */
|
||||
#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */
|
||||
|
||||
#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
|
||||
#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
|
||||
#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
|
||||
#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
|
||||
#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
|
||||
#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
|
||||
#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
|
||||
#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
|
||||
#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
|
||||
#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
|
||||
|
||||
#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
|
||||
#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
|
||||
#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
|
||||
|
||||
/* Section 4: Extended PHY Registers */
|
||||
|
||||
#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */
|
||||
|
||||
#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */
|
||||
#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */
|
||||
|
||||
|
||||
#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */
|
||||
#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */
|
||||
|
||||
/* ################## SPI peripheral configuration ########################## */
|
||||
|
||||
/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
|
||||
* Activated: CRC code is present inside driver
|
||||
* Deactivated: CRC code cleaned from driver
|
||||
*/
|
||||
|
||||
#define USE_SPI_CRC 1U
|
||||
|
||||
/* Includes ------------------------------------------------------------------*/
|
||||
/**
|
||||
* @brief Include module's header file
|
||||
*/
|
||||
|
||||
#ifdef HAL_RCC_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_rcc.h"
|
||||
#endif /* HAL_RCC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_GPIO_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_gpio.h"
|
||||
#endif /* HAL_GPIO_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_EXTI_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_exti.h"
|
||||
#endif /* HAL_EXTI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DMA_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_dma.h"
|
||||
#endif /* HAL_DMA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CORTEX_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_cortex.h"
|
||||
#endif /* HAL_CORTEX_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_ADC_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_adc.h"
|
||||
#endif /* HAL_ADC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CAN_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_can.h"
|
||||
#endif /* HAL_CAN_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRC_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_crc.h"
|
||||
#endif /* HAL_CRC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRYP_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_cryp.h"
|
||||
#endif /* HAL_CRYP_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DAC_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_dac.h"
|
||||
#endif /* HAL_DAC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DCMI_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_dcmi.h"
|
||||
#endif /* HAL_DCMI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_ETH_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_eth.h"
|
||||
#endif /* HAL_ETH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_FLASH_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_flash.h"
|
||||
#endif /* HAL_FLASH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SRAM_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_sram.h"
|
||||
#endif /* HAL_SRAM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NOR_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_nor.h"
|
||||
#endif /* HAL_NOR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NAND_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_nand.h"
|
||||
#endif /* HAL_NAND_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PCCARD_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_pccard.h"
|
||||
#endif /* HAL_PCCARD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_HASH_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_hash.h"
|
||||
#endif /* HAL_HASH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_I2C_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_i2c.h"
|
||||
#endif /* HAL_I2C_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_I2S_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_i2s.h"
|
||||
#endif /* HAL_I2S_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IWDG_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_iwdg.h"
|
||||
#endif /* HAL_IWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PWR_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_pwr.h"
|
||||
#endif /* HAL_PWR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RNG_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_rng.h"
|
||||
#endif /* HAL_RNG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RTC_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_rtc.h"
|
||||
#endif /* HAL_RTC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SD_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_sd.h"
|
||||
#endif /* HAL_SD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_spi.h"
|
||||
#endif /* HAL_SPI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_TIM_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_tim.h"
|
||||
#endif /* HAL_TIM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_uart.h"
|
||||
#endif /* HAL_UART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_USART_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_usart.h"
|
||||
#endif /* HAL_USART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IRDA_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_irda.h"
|
||||
#endif /* HAL_IRDA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SMARTCARD_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_smartcard.h"
|
||||
#endif /* HAL_SMARTCARD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_WWDG_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_wwdg.h"
|
||||
#endif /* HAL_WWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PCD_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_pcd.h"
|
||||
#endif /* HAL_PCD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_HCD_MODULE_ENABLED
|
||||
#include "stm32f2xx_hal_hcd.h"
|
||||
#endif /* HAL_HCD_MODULE_ENABLED */
|
||||
|
||||
/* Exported macro ------------------------------------------------------------*/
|
||||
#ifdef USE_FULL_ASSERT
|
||||
/**
|
||||
* @brief The assert_param macro is used for function's parameters check.
|
||||
* @param expr: If expr is false, it calls assert_failed function
|
||||
* which reports the name of the source file and the source
|
||||
* line number of the call that failed.
|
||||
* If expr is true, it returns no value.
|
||||
* @retval None
|
||||
*/
|
||||
#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
|
||||
/* Exported functions ------------------------------------------------------- */
|
||||
void assert_failed(uint8_t* file, uint32_t line);
|
||||
#else
|
||||
#define assert_param(expr) ((void)0U)
|
||||
#endif /* USE_FULL_ASSERT */
|
||||
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* __STM32F2xx_HAL_CONF_H */
|
||||
|
||||
|
||||
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
||||
@ -13,7 +13,7 @@ ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F3xx_HAL_Driver
|
||||
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F3xx
|
||||
|
||||
# All source paths should be relative to the top level.
|
||||
LD_FILE = hw/bsp/stm32f303disco/STM32F303VCTx_FLASH.ld
|
||||
LD_FILE = hw/bsp/$(BOARD)/STM32F303VCTx_FLASH.ld
|
||||
|
||||
SRC_C += \
|
||||
$(ST_CMSIS)/Source/Templates/system_stm32f3xx.c \
|
||||
|
||||
@ -13,7 +13,7 @@ ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F4xx_HAL_Driver
|
||||
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F4xx
|
||||
|
||||
# All source paths should be relative to the top level.
|
||||
LD_FILE = hw/bsp/stm32f407disco/STM32F407VGTx_FLASH.ld
|
||||
LD_FILE = hw/bsp/$(BOARD)/STM32F407VGTx_FLASH.ld
|
||||
|
||||
SRC_C += \
|
||||
$(ST_CMSIS)/Source/Templates/system_stm32f4xx.c \
|
||||
|
||||
@ -13,7 +13,7 @@ ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F4xx_HAL_Driver
|
||||
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F4xx
|
||||
|
||||
# All source paths should be relative to the top level.
|
||||
LD_FILE = hw/bsp/stm32f411disco/STM32F411VETx_FLASH.ld
|
||||
LD_FILE = hw/bsp/$(BOARD)/STM32F411VETx_FLASH.ld
|
||||
|
||||
SRC_C += \
|
||||
$(ST_CMSIS)/Source/Templates/system_stm32f4xx.c \
|
||||
|
||||
@ -13,7 +13,7 @@ ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F4xx_HAL_Driver
|
||||
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F4xx
|
||||
|
||||
# All source paths should be relative to the top level.
|
||||
LD_FILE = hw/bsp/stm32f412disco/STM32F412ZGTx_FLASH.ld
|
||||
LD_FILE = hw/bsp/$(BOARD)/STM32F412ZGTx_FLASH.ld
|
||||
|
||||
SRC_C += \
|
||||
$(ST_CMSIS)/Source/Templates/system_stm32f4xx.c \
|
||||
|
||||
@ -9,7 +9,7 @@ CFLAGS += \
|
||||
-nostdlib -nostartfiles \
|
||||
-DCFG_TUSB_MCU=OPT_MCU_STM32F7
|
||||
|
||||
# The -Wno-error=sign-compare line is required due to STM32F7xx_HAL_Driver.
|
||||
# Suppress following warnings/error is required due to STM32F7xx_HAL_Driver.
|
||||
CFLAGS += -Wno-error=shadow
|
||||
|
||||
ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver
|
||||
|
||||
@ -13,7 +13,7 @@ ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver
|
||||
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx
|
||||
|
||||
# All source paths should be relative to the top level.
|
||||
LD_FILE = hw/bsp/stm32h743nucleo/STM32H743ZITx_FLASH.ld
|
||||
LD_FILE = hw/bsp/$(BOARD)/STM32H743ZITx_FLASH.ld
|
||||
|
||||
SRC_C += \
|
||||
$(ST_CMSIS)/Source/Templates/system_stm32h7xx.c \
|
||||
|
||||
@ -27,29 +27,33 @@
|
||||
|
||||
#include "tusb_option.h"
|
||||
|
||||
#if TUSB_OPT_DEVICE_ENABLED && ( CFG_TUSB_MCU == OPT_MCU_STM32F4 || \
|
||||
#if TUSB_OPT_DEVICE_ENABLED && ( CFG_TUSB_MCU == OPT_MCU_STM32F2 || \
|
||||
CFG_TUSB_MCU == OPT_MCU_STM32F4 || \
|
||||
CFG_TUSB_MCU == OPT_MCU_STM32H7 || \
|
||||
CFG_TUSB_MCU == OPT_MCU_STM32F7)
|
||||
|
||||
// TODO Support OTG_HS
|
||||
// EP_MAX : Max number of bi-directional endpoints including EP0
|
||||
// EP_FIFO_SIZE : Size of dedicated USB SRAM
|
||||
#if CFG_TUSB_MCU == OPT_MCU_STM32F4
|
||||
#if CFG_TUSB_MCU == OPT_MCU_STM32F2
|
||||
#include "stm32f2xx.h"
|
||||
#define EP_MAX USB_OTG_FS_MAX_IN_ENDPOINTS
|
||||
#define EP_FIFO_SIZE USB_OTG_FS_TOTAL_FIFO_SIZE
|
||||
#elif CFG_TUSB_MCU == OPT_MCU_STM32F4
|
||||
#include "stm32f4xx.h"
|
||||
|
||||
#define EP_MAX USB_OTG_FS_MAX_IN_ENDPOINTS
|
||||
#define EP_FIFO_SIZE USB_OTG_FS_TOTAL_FIFO_SIZE
|
||||
#define EP_MAX USB_OTG_FS_MAX_IN_ENDPOINTS
|
||||
#define EP_FIFO_SIZE USB_OTG_FS_TOTAL_FIFO_SIZE
|
||||
#elif CFG_TUSB_MCU == OPT_MCU_STM32H7
|
||||
#include "stm32h7xx.h"
|
||||
|
||||
#define EP_MAX 9
|
||||
#define EP_FIFO_SIZE 4096
|
||||
#define EP_MAX 9
|
||||
#define EP_FIFO_SIZE 4096
|
||||
// TODO The official name of the USB FS peripheral on H7 is "USB2_OTG_FS".
|
||||
#else
|
||||
#elif CFG_TUSB_MCU == OPT_MCU_STM32F7
|
||||
#include "stm32f7xx.h"
|
||||
|
||||
#define EP_MAX 6
|
||||
#define EP_FIFO_SIZE 1280
|
||||
#define EP_MAX 6
|
||||
#define EP_FIFO_SIZE 1280
|
||||
#else
|
||||
#error "Unsupported MCUs"
|
||||
#endif
|
||||
|
||||
#include "device/dcd.h"
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user