/* USER CODE BEGIN Header */ /** ****************************************************************************** * @file stm32c0xx_hal_conf.h * @author MCD Application Team * @brief HAL configuration template file. * This file should be copied to the application folder and renamed * to stm32c0xx_hal_conf.h. ****************************************************************************** * @attention * * Copyright (c) 2021 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** */ /* USER CODE END Header */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef STM32C0xx_HAL_CONF_H #define STM32C0xx_HAL_CONF_H #ifdef __cplusplus extern "C" { #endif /* Exported types ------------------------------------------------------------*/ /* Exported constants --------------------------------------------------------*/ /* ########################## Module Selection ############################## */ /** * @brief This is the list of modules to be used in the HAL driver */ #define HAL_MODULE_ENABLED /* #define HAL_ADC_MODULE_ENABLED */ /* #define HAL_CRC_MODULE_ENABLED */ /* #define HAL_CRYP_MODULE_ENABLED */ /* #define HAL_I2C_MODULE_ENABLED */ /* #define HAL_I2S_MODULE_ENABLED */ /* #define HAL_IWDG_MODULE_ENABLED */ /* #define HAL_IRDA_MODULE_ENABLED */ /* #define HAL_PCD_MODULE_ENABLED */ /* #define HAL_HCD_MODULE_ENABLED */ /* #define HAL_RNG_MODULE_ENABLED */ /* #define HAL_RTC_MODULE_ENABLED */ /* #define HAL_SMARTCARD_MODULE_ENABLED */ /* #define HAL_SMBUS_MODULE_ENABLED */ /* #define HAL_SPI_MODULE_ENABLED */ /* #define HAL_TIM_MODULE_ENABLED */ /* #define HAL_USART_MODULE_ENABLED */ /* #define HAL_WWDG_MODULE_ENABLED */ #define HAL_GPIO_MODULE_ENABLED #define HAL_EXTI_MODULE_ENABLED #define HAL_DMA_MODULE_ENABLED #define HAL_RCC_MODULE_ENABLED #define HAL_FLASH_MODULE_ENABLED #define HAL_PWR_MODULE_ENABLED #define HAL_CORTEX_MODULE_ENABLED #define HAL_UART_MODULE_ENABLED /* ########################## Register Callbacks selection ############################## */ /** * @brief Set below the peripheral configuration to "1U" to add the support * of HAL callback registration/unregistration feature for the HAL * driver(s). This allows user application to provide specific callback * functions thanks to HAL_PPP_RegisterCallback() rather than overwriting * the default weak callback functions (see each stm32c0xx_hal_ppp.h file * for possible callback identifiers defined in HAL_PPP_CallbackIDTypeDef * for each PPP peripheral). */ #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ #define USE_HAL_IWDG_REGISTER_CALLBACKS 0U /* IWDG register callback disabled */ #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ /* ########################## Oscillator Values adaptation ####################*/ /** * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. * This value is used by the RCC HAL module to compute the system frequency * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined (HSE_VALUE) #define HSE_VALUE (8000000U) /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined (HSE_STARTUP_TIMEOUT) #define HSE_STARTUP_TIMEOUT (100UL) /*!< Time out for HSE start up, in ms */ #endif /* HSE_STARTUP_TIMEOUT */ /** * @brief Internal High Speed oscillator (HSI) value. * This value is used by the RCC HAL module to compute the system frequency * (when HSI is used as system clock source, directly or through the PLL). */ #if !defined (HSI_VALUE) #define HSI_VALUE (48000000UL) /*!< Value of the Internal oscillator in Hz*/ #endif /* HSI_VALUE */ /** * @brief Internal Low Speed oscillator (LSI) value. */ #if !defined (LSI_VALUE) #define LSI_VALUE (32000UL) /*!< LSI Typical Value in Hz*/ #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature.*/ #if !defined (LSI_STARTUP_TIME) #define LSI_STARTUP_TIME 130UL /*!< Time out for LSI start up, in ms */ #endif /* LSI_STARTUP_TIME */ /** * @brief External Low Speed oscillator (LSE) value. * This value is used by the UART, RTC HAL module to compute the system frequency */ #if !defined (LSE_VALUE) #define LSE_VALUE (32768UL) /*!< Value of the External oscillator in Hz*/ #endif /* LSE_VALUE */ #if !defined (LSE_STARTUP_TIMEOUT) #define LSE_STARTUP_TIMEOUT (5000UL) /*!< Time out for LSE start up, in ms */ #endif /* LSE_STARTUP_TIMEOUT */ /** * @brief External clock source for I2S1 peripheral * This value is used by the RCC HAL module to compute the I2S1 clock source * frequency. */ #if !defined (EXTERNAL_I2S1_CLOCK_VALUE) #define EXTERNAL_I2S1_CLOCK_VALUE (12288000UL) /*!< Value of the I2S1 External clock source in Hz*/ #endif /* EXTERNAL_I2S1_CLOCK_VALUE */ /* Tip: To avoid modifying this file each time you need to use different HSE, === you can define the HSE value in your toolchain compiler preprocessor. */ /* ########################### System Configuration ######################### */ /** * @brief This is the HAL system configuration section */ #define VDD_VALUE (3300UL) /*!< Value of VDD in mv */ #define TICK_INT_PRIORITY 3U /*!< tick interrupt priority */ #define USE_RTOS 0U #define PREFETCH_ENABLE 0U #define INSTRUCTION_CACHE_ENABLE 1U /* ########################## Assert Selection ############################## */ /** * @brief Uncomment the line below to expanse the "assert_param" macro in the * HAL drivers code */ /* #define USE_FULL_ASSERT 1U */ /* Includes ------------------------------------------------------------------*/ /** * @brief Include modules header file */ #ifdef HAL_RCC_MODULE_ENABLED #include "stm32c0xx_hal_rcc.h" #endif /* HAL_RCC_MODULE_ENABLED */ #ifdef HAL_GPIO_MODULE_ENABLED #include "stm32c0xx_hal_gpio.h" #endif /* HAL_GPIO_MODULE_ENABLED */ #ifdef HAL_DMA_MODULE_ENABLED #include "stm32c0xx_hal_dma.h" #endif /* HAL_DMA_MODULE_ENABLED */ #ifdef HAL_CORTEX_MODULE_ENABLED #include "stm32c0xx_hal_cortex.h" #endif /* HAL_CORTEX_MODULE_ENABLED */ #ifdef HAL_ADC_MODULE_ENABLED #include "stm32c0xx_hal_adc.h" #include "stm32c0xx_hal_adc_ex.h" #endif /* HAL_ADC_MODULE_ENABLED */ #ifdef HAL_CRC_MODULE_ENABLED #include "stm32c0xx_hal_crc.h" #endif /* HAL_CRC_MODULE_ENABLED */ #ifdef HAL_EXTI_MODULE_ENABLED #include "stm32c0xx_hal_exti.h" #endif /* HAL_EXTI_MODULE_ENABLED */ #ifdef HAL_FLASH_MODULE_ENABLED #include "stm32c0xx_hal_flash.h" #endif /* HAL_FLASH_MODULE_ENABLED */ #ifdef HAL_I2C_MODULE_ENABLED #include "stm32c0xx_hal_i2c.h" #endif /* HAL_I2C_MODULE_ENABLED */ #ifdef HAL_I2S_MODULE_ENABLED #include "stm32c0xx_hal_i2s.h" #endif /* HAL_I2S_MODULE_ENABLED */ #ifdef HAL_IRDA_MODULE_ENABLED #include "stm32c0xx_hal_irda.h" #endif /* HAL_IRDA_MODULE_ENABLED */ #ifdef HAL_IWDG_MODULE_ENABLED #include "stm32c0xx_hal_iwdg.h" #endif /* HAL_IWDG_MODULE_ENABLED */ #ifdef HAL_PWR_MODULE_ENABLED #include "stm32c0xx_hal_pwr.h" #endif /* HAL_PWR_MODULE_ENABLED */ #ifdef HAL_RTC_MODULE_ENABLED #include "stm32c0xx_hal_rtc.h" #endif /* HAL_RTC_MODULE_ENABLED */ #ifdef HAL_SMARTCARD_MODULE_ENABLED #include "stm32c0xx_hal_smartcard.h" #endif /* HAL_SMARTCARD_MODULE_ENABLED */ #ifdef HAL_SMBUS_MODULE_ENABLED #include "stm32c0xx_hal_smbus.h" #endif /* HAL_SMBUS_MODULE_ENABLED */ #ifdef HAL_SPI_MODULE_ENABLED #include "stm32c0xx_hal_spi.h" #endif /* HAL_SPI_MODULE_ENABLED */ #ifdef HAL_TIM_MODULE_ENABLED #include "stm32c0xx_hal_tim.h" #endif /* HAL_TIM_MODULE_ENABLED */ #ifdef HAL_UART_MODULE_ENABLED #include "stm32c0xx_hal_uart.h" #endif /* HAL_UART_MODULE_ENABLED */ #ifdef HAL_USART_MODULE_ENABLED #include "stm32c0xx_hal_usart.h" #endif /* HAL_USART_MODULE_ENABLED */ #ifdef HAL_WWDG_MODULE_ENABLED #include "stm32c0xx_hal_wwdg.h" #endif /* HAL_WWDG_MODULE_ENABLED */ #ifdef HAL_PCD_MODULE_ENABLED #include "stm32c0xx_hal_pcd.h" #endif /* HAL_PCD_MODULE_ENABLED */ #ifdef HAL_HCD_MODULE_ENABLED #include "stm32c0xx_hal_hcd.h" #endif /* HAL_HCD_MODULE_ENABLED */ /* Exported macro ------------------------------------------------------------*/ #ifdef USE_FULL_ASSERT /** * @brief The assert_param macro is used for functions parameters check. * @param expr If expr is false, it calls assert_failed function * which reports the name of the source file and the source * line number of the call that failed. * If expr is true, it returns no value. * @retval None */ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) /* Exported functions ------------------------------------------------------- */ void assert_failed(uint8_t *file, uint32_t line); #else #define assert_param(expr) ((void)0U) #endif /* USE_FULL_ASSERT */ #ifdef __cplusplus } #endif #endif /* STM32C0xx_HAL_CONF_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/