mirror of
https://github.com/hathach/tinyusb.git
synced 2025-02-07 05:54:11 +08:00
104 lines
3.3 KiB
C
104 lines
3.3 KiB
C
/* metadata:
|
|
name: LPCXpresso11U37
|
|
url: https://www.nxp.com/design/design-center/development-boards-and-designs/OM13074
|
|
*/
|
|
|
|
#ifndef BOARD_H
|
|
#define BOARD_H
|
|
|
|
#define LED_PORT 1
|
|
#define LED_PIN 24
|
|
#define LED_STATE_ON 0
|
|
|
|
// Wake up Switch
|
|
#define BUTTON_PORT 0
|
|
#define BUTTON_PIN 16
|
|
#define BUTTON_STATE_ACTIVE 0
|
|
|
|
/* System oscillator rate and RTC oscillator rate */
|
|
const uint32_t OscRateIn = 12000000;
|
|
const uint32_t ExtRateIn = 0;
|
|
|
|
/* Pin muxing table, only items that need changing from their default pin
|
|
state are in this table. Not every pin is mapped. */
|
|
/* IOCON pin definitions for pin muxing */
|
|
typedef struct {
|
|
uint32_t port : 8; /* Pin port */
|
|
uint32_t pin : 8; /* Pin number */
|
|
uint32_t modefunc : 16; /* Function and mode */
|
|
} PINMUX_GRP_T;
|
|
|
|
static const PINMUX_GRP_T pinmuxing[] = {
|
|
{0, 3, (IOCON_FUNC1 | IOCON_MODE_INACT | IOCON_DIGMODE_EN)}, // USB VBUS
|
|
{0, 6, (IOCON_FUNC1 | IOCON_MODE_INACT)}, /* PIO0_6 used for USB_CONNECT */
|
|
|
|
{0, 18, (IOCON_FUNC1 | IOCON_MODE_INACT | IOCON_DIGMODE_EN)}, // UART0 RX
|
|
{0, 19, (IOCON_FUNC1 | IOCON_MODE_INACT | IOCON_DIGMODE_EN)}, // UART0 TX
|
|
};
|
|
|
|
/* Setup system clocking */
|
|
static inline void Chip_SetupXtalClocking(void) {
|
|
volatile int i;
|
|
|
|
/* Powerup main oscillator */
|
|
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSOSC_PD);
|
|
|
|
/* Wait 200us for OSC to be stablized, no status
|
|
indication, dummy wait. */
|
|
for (i = 0; i < 0x100; i++) {}
|
|
|
|
/* Set system PLL input to main oscillator */
|
|
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_MAINOSC);
|
|
|
|
/* Power down PLL to change the PLL divider ratio */
|
|
Chip_SYSCTL_PowerDown(SYSCTL_POWERDOWN_SYSPLL_PD);
|
|
|
|
/* Setup PLL for main oscillator rate (FCLKIN = 12MHz) * 4 = 48MHz
|
|
MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
|
|
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
|
|
FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range) */
|
|
Chip_Clock_SetupSystemPLL(3, 1);
|
|
|
|
/* Powerup system PLL */
|
|
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSPLL_PD);
|
|
|
|
/* Wait for PLL to lock */
|
|
while (!Chip_Clock_IsSystemPLLLocked()) {}
|
|
|
|
/* Set system clock divider to 1 */
|
|
Chip_Clock_SetSysClockDiv(1);
|
|
|
|
/* Setup FLASH access to 3 clocks */
|
|
Chip_FMC_SetFLASHAccess(FLASHTIM_50MHZ_CPU);
|
|
|
|
/* Set main clock source to the system PLL. This will drive 48MHz
|
|
for the main clock and 48MHz for the system clock */
|
|
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
|
|
|
|
/* Set USB PLL input to main oscillator */
|
|
Chip_Clock_SetUSBPLLSource(SYSCTL_PLLCLKSRC_MAINOSC);
|
|
/* Setup USB PLL (FCLKIN = 12MHz) * 4 = 48MHz
|
|
MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
|
|
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
|
|
FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range) */
|
|
Chip_Clock_SetupUSBPLL(3, 1);
|
|
|
|
/* Powerup USB PLL */
|
|
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_USBPLL_PD);
|
|
|
|
/* Wait for PLL to lock */
|
|
while (!Chip_Clock_IsUSBPLLLocked()) {}
|
|
}
|
|
|
|
static inline void Chip_USB_Init(void) {
|
|
/* enable USB main clock */
|
|
Chip_Clock_SetUSBClockSource(SYSCTL_USBCLKSRC_PLLOUT, 1);
|
|
/* Enable AHB clock to the USB block and USB RAM. */
|
|
Chip_Clock_EnablePeriphClock(SYSCTL_CLOCK_USB);
|
|
Chip_Clock_EnablePeriphClock(SYSCTL_CLOCK_USBRAM);
|
|
/* power UP USB Phy */
|
|
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_USBPAD_PD);
|
|
}
|
|
|
|
#endif
|