Add makefiles for VU13P variant of HTG-9200

Signed-off-by: Alex Forencich <alex@alexforencich.com>

example/HTG9200/fpga_25g/README.md

@@ -8,7 +8,7 @@ The design by default listens to UDP port 1234 at IP address 192.168.1.128 and
 will echo back any packets received.  The design will also respond correctly
 to ARP requests.  
 
-*  FPGA: xcvu9p-flgb2104-2-e
+*  FPGA: xcvu9p-flgb2104-2-e or xcvu13p-fhgb2104-2-e
 *  PHY: 10G BASE-R PHY IP core and internal GTY transceiver
 
 ## How to build

example/HTG9200/fpga_25g/fpga.xdc

@@ -1,5 +1,6 @@
 # XDC constraints for the HiTech Global HTG-9200 board
 # part: xcvu9p-flgb2104-2-e
+# part: xcvu13p-fhgb2104-2-e
 
 # General configuration
 set_property CFGBVS GND                                [current_design]

example/HTG9200/fpga_25g/fpga_10g_vu13p/Makefile

@@ -0,0 +1,116 @@
+
+# FPGA settings
+FPGA_PART = xcvu13p-fhgb2104-2-e
+FPGA_TOP = fpga
+FPGA_ARCH = virtexuplus
+
+# Files for synthesis
+SYN_FILES = rtl/fpga.v
+SYN_FILES += rtl/fpga_core.v
+SYN_FILES += rtl/eth_xcvr_phy_wrapper.v
+SYN_FILES += rtl/eth_xcvr_phy_quad_wrapper.v
+SYN_FILES += rtl/debounce_switch.v
+SYN_FILES += rtl/sync_signal.v
+SYN_FILES += rtl/i2c_master.v
+SYN_FILES += pll/si5341_i2c_init.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g_fifo.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_rx_64.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_tx_64.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_if.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_frame_sync.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_ber_mon.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_watchdog.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx_if.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_dec_64.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_enc_64.v
+SYN_FILES += lib/eth/rtl/lfsr.v
+SYN_FILES += lib/eth/rtl/eth_axis_rx.v
+SYN_FILES += lib/eth/rtl/eth_axis_tx.v
+SYN_FILES += lib/eth/rtl/udp_complete_64.v
+SYN_FILES += lib/eth/rtl/udp_checksum_gen_64.v
+SYN_FILES += lib/eth/rtl/udp_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_rx_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_complete_64.v
+SYN_FILES += lib/eth/rtl/ip_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_rx_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_arb_mux.v
+SYN_FILES += lib/eth/rtl/arp.v
+SYN_FILES += lib/eth/rtl/arp_cache.v
+SYN_FILES += lib/eth/rtl/arp_eth_rx.v
+SYN_FILES += lib/eth/rtl/arp_eth_tx.v
+SYN_FILES += lib/eth/rtl/eth_arb_mux.v
+SYN_FILES += lib/eth/lib/axis/rtl/arbiter.v
+SYN_FILES += lib/eth/lib/axis/rtl/priority_encoder.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo_adapter.v
+SYN_FILES += lib/eth/lib/axis/rtl/sync_reset.v
+
+# XDC files
+XDC_FILES = fpga.xdc
+XDC_FILES += lib/eth/syn/vivado/eth_mac_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/axis_async_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/sync_reset.tcl
+
+# IP
+IP_TCL_FILES += ip/eth_xcvr_gt.tcl
+
+# Configuration
+CONFIG_TCL_FILES = ./config.tcl
+
+include ../common/vivado.mk
+
+program: $(FPGA_TOP).bit
+	echo "open_hw" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(FPGA_TOP).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+%_primary.mcs %_secondary.mcs %_primary.prm %_secondary.prm: %.bit
+	echo "write_cfgmem -force -format mcs -size 128 -interface SPIx8 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in _primary.mcs _secondary.mcs _primary.prm _secondary.prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;
+
+flash: $(FPGA_TOP)_primary.mcs $(FPGA_TOP)_secondary.mcs $(FPGA_TOP)_primary.prm $(FPGA_TOP)_secondary.prm
+	echo "open_hw" > flash.tcl
+	echo "connect_hw_server" >> flash.tcl
+	echo "open_hw_target" >> flash.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> flash.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> flash.tcl
+	echo "create_hw_cfgmem -hw_device [current_hw_device] [lindex [get_cfgmem_parts {s25fl512s-spi-x1_x2_x4_x8}] 0]" >> flash.tcl
+	echo "current_hw_cfgmem -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM [current_hw_device]]" >> flash.tcl
+	echo "set_property PROGRAM.FILES [list \"$(FPGA_TOP)_primary.mcs\" \"$(FPGA_TOP)_secondary.mcs\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.PRM_FILES [list \"$(FPGA_TOP)_primary.prm\" \"$(FPGA_TOP)_secondary.prm\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ERASE 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CFG_PROGRAM 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.VERIFY 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CHECKSUM 0 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ADDRESS_RANGE {use_file} [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.UNUSED_PIN_TERMINATION {pull-none} [current_hw_cfgmem]" >> flash.tcl
+	echo "create_hw_bitstream -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM_BITFILE [current_hw_device]]" >> flash.tcl
+	echo "program_hw_devices [current_hw_device]" >> flash.tcl
+	echo "refresh_hw_device [current_hw_device]" >> flash.tcl
+	echo "program_hw_cfgmem -hw_cfgmem [current_hw_cfgmem]" >> flash.tcl
+	echo "boot_hw_device [current_hw_device]" >> flash.tcl
+	echo "exit" >> flash.tcl
+	vivado -nojournal -nolog -mode batch -source flash.tcl
+

example/HTG9200/fpga_25g/fpga_vu13p/Makefile

@@ -0,0 +1,116 @@
+
+# FPGA settings
+FPGA_PART = xcvu13p-fhgb2104-2-e
+FPGA_TOP = fpga
+FPGA_ARCH = virtexuplus
+
+# Files for synthesis
+SYN_FILES = rtl/fpga.v
+SYN_FILES += rtl/fpga_core.v
+SYN_FILES += rtl/eth_xcvr_phy_wrapper.v
+SYN_FILES += rtl/eth_xcvr_phy_quad_wrapper.v
+SYN_FILES += rtl/debounce_switch.v
+SYN_FILES += rtl/sync_signal.v
+SYN_FILES += rtl/i2c_master.v
+SYN_FILES += pll/si5341_i2c_init.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g_fifo.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_rx_64.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_tx_64.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_if.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_frame_sync.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_ber_mon.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_watchdog.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx_if.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_dec_64.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_enc_64.v
+SYN_FILES += lib/eth/rtl/lfsr.v
+SYN_FILES += lib/eth/rtl/eth_axis_rx.v
+SYN_FILES += lib/eth/rtl/eth_axis_tx.v
+SYN_FILES += lib/eth/rtl/udp_complete_64.v
+SYN_FILES += lib/eth/rtl/udp_checksum_gen_64.v
+SYN_FILES += lib/eth/rtl/udp_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_rx_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_complete_64.v
+SYN_FILES += lib/eth/rtl/ip_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_rx_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_arb_mux.v
+SYN_FILES += lib/eth/rtl/arp.v
+SYN_FILES += lib/eth/rtl/arp_cache.v
+SYN_FILES += lib/eth/rtl/arp_eth_rx.v
+SYN_FILES += lib/eth/rtl/arp_eth_tx.v
+SYN_FILES += lib/eth/rtl/eth_arb_mux.v
+SYN_FILES += lib/eth/lib/axis/rtl/arbiter.v
+SYN_FILES += lib/eth/lib/axis/rtl/priority_encoder.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo_adapter.v
+SYN_FILES += lib/eth/lib/axis/rtl/sync_reset.v
+
+# XDC files
+XDC_FILES = fpga.xdc
+XDC_FILES += lib/eth/syn/vivado/eth_mac_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/axis_async_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/sync_reset.tcl
+
+# IP
+IP_TCL_FILES += ip/eth_xcvr_gt.tcl
+
+# Configuration
+CONFIG_TCL_FILES = ./config.tcl
+
+include ../common/vivado.mk
+
+program: $(FPGA_TOP).bit
+	echo "open_hw" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(FPGA_TOP).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+%_primary.mcs %_secondary.mcs %_primary.prm %_secondary.prm: %.bit
+	echo "write_cfgmem -force -format mcs -size 128 -interface SPIx8 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in _primary.mcs _secondary.mcs _primary.prm _secondary.prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;
+
+flash: $(FPGA_TOP)_primary.mcs $(FPGA_TOP)_secondary.mcs $(FPGA_TOP)_primary.prm $(FPGA_TOP)_secondary.prm
+	echo "open_hw" > flash.tcl
+	echo "connect_hw_server" >> flash.tcl
+	echo "open_hw_target" >> flash.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> flash.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> flash.tcl
+	echo "create_hw_cfgmem -hw_device [current_hw_device] [lindex [get_cfgmem_parts {s25fl512s-spi-x1_x2_x4_x8}] 0]" >> flash.tcl
+	echo "current_hw_cfgmem -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM [current_hw_device]]" >> flash.tcl
+	echo "set_property PROGRAM.FILES [list \"$(FPGA_TOP)_primary.mcs\" \"$(FPGA_TOP)_secondary.mcs\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.PRM_FILES [list \"$(FPGA_TOP)_primary.prm\" \"$(FPGA_TOP)_secondary.prm\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ERASE 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CFG_PROGRAM 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.VERIFY 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CHECKSUM 0 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ADDRESS_RANGE {use_file} [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.UNUSED_PIN_TERMINATION {pull-none} [current_hw_cfgmem]" >> flash.tcl
+	echo "create_hw_bitstream -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM_BITFILE [current_hw_device]]" >> flash.tcl
+	echo "program_hw_devices [current_hw_device]" >> flash.tcl
+	echo "refresh_hw_device [current_hw_device]" >> flash.tcl
+	echo "program_hw_cfgmem -hw_cfgmem [current_hw_cfgmem]" >> flash.tcl
+	echo "boot_hw_device [current_hw_device]" >> flash.tcl
+	echo "exit" >> flash.tcl
+	vivado -nojournal -nolog -mode batch -source flash.tcl
+

example/HTG9200/fpga_fmc_htg_6qsfp_25g/README.md

@@ -8,7 +8,7 @@ The design by default listens to UDP port 1234 at IP address 192.168.1.128 and w
 
 The design is configured to run all 15 QSFP28 modules synchronous to the GTY reference oscillator (U47) on the HTG-9200.  This is done by forwarding the MGT reference clock for QSFP1 through the FPGA to the SYNC_C2M pins on the FMC+, which is connected as a reference input to the Si5341 PLL (U7) on the FMC+.
 
-*  FPGA: xcvu9p-flgb2104-2-e
+*  FPGA: xcvu9p-flgb2104-2-e or xcvu13p-fhgb2104-2-e
 *  PHY: 10G BASE-R PHY IP core and internal GTY transceiver
 
 ## How to build

example/HTG9200/fpga_fmc_htg_6qsfp_25g/fpga.xdc

@@ -1,5 +1,6 @@
 # XDC constraints for the HiTech Global HTG-9200 board
 # part: xcvu9p-flgb2104-2-e
+# part: xcvu13p-fhgb2104-2-e
 
 # General configuration
 set_property CFGBVS GND                                [current_design]

example/HTG9200/fpga_fmc_htg_6qsfp_25g/fpga_10g_vu13p/Makefile

@@ -0,0 +1,116 @@
+
+# FPGA settings
+FPGA_PART = xcvu13p-fhgb2104-2-e
+FPGA_TOP = fpga
+FPGA_ARCH = virtexuplus
+
+# Files for synthesis
+SYN_FILES = rtl/fpga.v
+SYN_FILES += rtl/fpga_core.v
+SYN_FILES += rtl/eth_xcvr_phy_wrapper.v
+SYN_FILES += rtl/eth_xcvr_phy_quad_wrapper.v
+SYN_FILES += rtl/debounce_switch.v
+SYN_FILES += rtl/sync_signal.v
+SYN_FILES += rtl/i2c_master.v
+SYN_FILES += pll/si5341_i2c_init.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g_fifo.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_rx_64.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_tx_64.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_if.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_frame_sync.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_ber_mon.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_watchdog.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx_if.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_dec_64.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_enc_64.v
+SYN_FILES += lib/eth/rtl/lfsr.v
+SYN_FILES += lib/eth/rtl/eth_axis_rx.v
+SYN_FILES += lib/eth/rtl/eth_axis_tx.v
+SYN_FILES += lib/eth/rtl/udp_complete_64.v
+SYN_FILES += lib/eth/rtl/udp_checksum_gen_64.v
+SYN_FILES += lib/eth/rtl/udp_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_rx_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_complete_64.v
+SYN_FILES += lib/eth/rtl/ip_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_rx_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_arb_mux.v
+SYN_FILES += lib/eth/rtl/arp.v
+SYN_FILES += lib/eth/rtl/arp_cache.v
+SYN_FILES += lib/eth/rtl/arp_eth_rx.v
+SYN_FILES += lib/eth/rtl/arp_eth_tx.v
+SYN_FILES += lib/eth/rtl/eth_arb_mux.v
+SYN_FILES += lib/eth/lib/axis/rtl/arbiter.v
+SYN_FILES += lib/eth/lib/axis/rtl/priority_encoder.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo_adapter.v
+SYN_FILES += lib/eth/lib/axis/rtl/sync_reset.v
+
+# XDC files
+XDC_FILES = fpga.xdc
+XDC_FILES += lib/eth/syn/vivado/eth_mac_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/axis_async_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/sync_reset.tcl
+
+# IP
+IP_TCL_FILES += ip/eth_xcvr_gt.tcl
+
+# Configuration
+CONFIG_TCL_FILES = ./config.tcl
+
+include ../common/vivado.mk
+
+program: $(FPGA_TOP).bit
+	echo "open_hw" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(FPGA_TOP).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+%_primary.mcs %_secondary.mcs %_primary.prm %_secondary.prm: %.bit
+	echo "write_cfgmem -force -format mcs -size 128 -interface SPIx8 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in _primary.mcs _secondary.mcs _primary.prm _secondary.prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;
+
+flash: $(FPGA_TOP)_primary.mcs $(FPGA_TOP)_secondary.mcs $(FPGA_TOP)_primary.prm $(FPGA_TOP)_secondary.prm
+	echo "open_hw" > flash.tcl
+	echo "connect_hw_server" >> flash.tcl
+	echo "open_hw_target" >> flash.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> flash.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> flash.tcl
+	echo "create_hw_cfgmem -hw_device [current_hw_device] [lindex [get_cfgmem_parts {s25fl512s-spi-x1_x2_x4_x8}] 0]" >> flash.tcl
+	echo "current_hw_cfgmem -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM [current_hw_device]]" >> flash.tcl
+	echo "set_property PROGRAM.FILES [list \"$(FPGA_TOP)_primary.mcs\" \"$(FPGA_TOP)_secondary.mcs\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.PRM_FILES [list \"$(FPGA_TOP)_primary.prm\" \"$(FPGA_TOP)_secondary.prm\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ERASE 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CFG_PROGRAM 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.VERIFY 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CHECKSUM 0 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ADDRESS_RANGE {use_file} [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.UNUSED_PIN_TERMINATION {pull-none} [current_hw_cfgmem]" >> flash.tcl
+	echo "create_hw_bitstream -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM_BITFILE [current_hw_device]]" >> flash.tcl
+	echo "program_hw_devices [current_hw_device]" >> flash.tcl
+	echo "refresh_hw_device [current_hw_device]" >> flash.tcl
+	echo "program_hw_cfgmem -hw_cfgmem [current_hw_cfgmem]" >> flash.tcl
+	echo "boot_hw_device [current_hw_device]" >> flash.tcl
+	echo "exit" >> flash.tcl
+	vivado -nojournal -nolog -mode batch -source flash.tcl
+

example/HTG9200/fpga_fmc_htg_6qsfp_25g/fpga_10g_vu13p/config.tcl

@@ -0,0 +1,50 @@
+# Copyright (c) 2023 Alex Forencich
+#
+# Permission is hereby granted, free of charge, to any person obtaining a copy
+# of this software and associated documentation files (the "Software"), to deal
+# in the Software without restriction, including without limitation the rights
+# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+# copies of the Software, and to permit persons to whom the Software is
+# furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice shall be included in
+# all copies or substantial portions of the Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+# THE SOFTWARE.
+
+# Transceiver configuration
+set eth_xcvr_freerun_freq {125}
+set eth_xcvr_line_rate {10.3125}
+set eth_xcvr_sec_line_rate {0}
+set eth_xcvr_refclk_freq {161.1328125}
+set eth_xcvr_qpll_fracn [expr {int(fmod($eth_xcvr_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_sec_qpll_fracn [expr {int(fmod($eth_xcvr_sec_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_rx_eq_mode {DFE}
+
+set xcvr_config [dict create]
+
+dict set xcvr_config CONFIG.TX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.TX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.TX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.RX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.RX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_EQ_MODE $eth_xcvr_rx_eq_mode
+if {$eth_xcvr_sec_line_rate != 0} {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE true
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_FRACN_NUMERATOR $eth_xcvr_sec_qpll_fracn
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_LINE_RATE $eth_xcvr_sec_line_rate
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+} else {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE false
+}
+dict set xcvr_config CONFIG.FREERUN_FREQUENCY $eth_xcvr_freerun_freq
+
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_full]
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_channel]

example/HTG9200/fpga_fmc_htg_6qsfp_25g/fpga_10g_vu9p/config.tcl

@@ -0,0 +1,50 @@
+# Copyright (c) 2023 Alex Forencich
+#
+# Permission is hereby granted, free of charge, to any person obtaining a copy
+# of this software and associated documentation files (the "Software"), to deal
+# in the Software without restriction, including without limitation the rights
+# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+# copies of the Software, and to permit persons to whom the Software is
+# furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice shall be included in
+# all copies or substantial portions of the Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+# THE SOFTWARE.
+
+# Transceiver configuration
+set eth_xcvr_freerun_freq {125}
+set eth_xcvr_line_rate {10.3125}
+set eth_xcvr_sec_line_rate {0}
+set eth_xcvr_refclk_freq {161.1328125}
+set eth_xcvr_qpll_fracn [expr {int(fmod($eth_xcvr_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_sec_qpll_fracn [expr {int(fmod($eth_xcvr_sec_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_rx_eq_mode {DFE}
+
+set xcvr_config [dict create]
+
+dict set xcvr_config CONFIG.TX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.TX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.TX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.RX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.RX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_EQ_MODE $eth_xcvr_rx_eq_mode
+if {$eth_xcvr_sec_line_rate != 0} {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE true
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_FRACN_NUMERATOR $eth_xcvr_sec_qpll_fracn
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_LINE_RATE $eth_xcvr_sec_line_rate
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+} else {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE false
+}
+dict set xcvr_config CONFIG.FREERUN_FREQUENCY $eth_xcvr_freerun_freq
+
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_full]
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_channel]

example/HTG9200/fpga_fmc_htg_6qsfp_25g/fpga_vu13p/Makefile

@@ -0,0 +1,116 @@
+
+# FPGA settings
+FPGA_PART = xcvu13p-fhgb2104-2-e
+FPGA_TOP = fpga
+FPGA_ARCH = virtexuplus
+
+# Files for synthesis
+SYN_FILES = rtl/fpga.v
+SYN_FILES += rtl/fpga_core.v
+SYN_FILES += rtl/eth_xcvr_phy_wrapper.v
+SYN_FILES += rtl/eth_xcvr_phy_quad_wrapper.v
+SYN_FILES += rtl/debounce_switch.v
+SYN_FILES += rtl/sync_signal.v
+SYN_FILES += rtl/i2c_master.v
+SYN_FILES += pll/si5341_i2c_init.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g_fifo.v
+SYN_FILES += lib/eth/rtl/eth_mac_10g.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_rx_64.v
+SYN_FILES += lib/eth/rtl/axis_xgmii_tx_64.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_if.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_frame_sync.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_ber_mon.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_rx_watchdog.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx.v
+SYN_FILES += lib/eth/rtl/eth_phy_10g_tx_if.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_dec_64.v
+SYN_FILES += lib/eth/rtl/xgmii_baser_enc_64.v
+SYN_FILES += lib/eth/rtl/lfsr.v
+SYN_FILES += lib/eth/rtl/eth_axis_rx.v
+SYN_FILES += lib/eth/rtl/eth_axis_tx.v
+SYN_FILES += lib/eth/rtl/udp_complete_64.v
+SYN_FILES += lib/eth/rtl/udp_checksum_gen_64.v
+SYN_FILES += lib/eth/rtl/udp_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_rx_64.v
+SYN_FILES += lib/eth/rtl/udp_ip_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_complete_64.v
+SYN_FILES += lib/eth/rtl/ip_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_rx_64.v
+SYN_FILES += lib/eth/rtl/ip_eth_tx_64.v
+SYN_FILES += lib/eth/rtl/ip_arb_mux.v
+SYN_FILES += lib/eth/rtl/arp.v
+SYN_FILES += lib/eth/rtl/arp_cache.v
+SYN_FILES += lib/eth/rtl/arp_eth_rx.v
+SYN_FILES += lib/eth/rtl/arp_eth_tx.v
+SYN_FILES += lib/eth/rtl/eth_arb_mux.v
+SYN_FILES += lib/eth/lib/axis/rtl/arbiter.v
+SYN_FILES += lib/eth/lib/axis/rtl/priority_encoder.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo.v
+SYN_FILES += lib/eth/lib/axis/rtl/axis_async_fifo_adapter.v
+SYN_FILES += lib/eth/lib/axis/rtl/sync_reset.v
+
+# XDC files
+XDC_FILES = fpga.xdc
+XDC_FILES += lib/eth/syn/vivado/eth_mac_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/axis_async_fifo.tcl
+XDC_FILES += lib/eth/lib/axis/syn/vivado/sync_reset.tcl
+
+# IP
+IP_TCL_FILES += ip/eth_xcvr_gt.tcl
+
+# Configuration
+CONFIG_TCL_FILES = ./config.tcl
+
+include ../common/vivado.mk
+
+program: $(FPGA_TOP).bit
+	echo "open_hw" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(FPGA_TOP).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+%_primary.mcs %_secondary.mcs %_primary.prm %_secondary.prm: %.bit
+	echo "write_cfgmem -force -format mcs -size 128 -interface SPIx8 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in _primary.mcs _secondary.mcs _primary.prm _secondary.prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;
+
+flash: $(FPGA_TOP)_primary.mcs $(FPGA_TOP)_secondary.mcs $(FPGA_TOP)_primary.prm $(FPGA_TOP)_secondary.prm
+	echo "open_hw" > flash.tcl
+	echo "connect_hw_server" >> flash.tcl
+	echo "open_hw_target" >> flash.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> flash.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> flash.tcl
+	echo "create_hw_cfgmem -hw_device [current_hw_device] [lindex [get_cfgmem_parts {s25fl512s-spi-x1_x2_x4_x8}] 0]" >> flash.tcl
+	echo "current_hw_cfgmem -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM [current_hw_device]]" >> flash.tcl
+	echo "set_property PROGRAM.FILES [list \"$(FPGA_TOP)_primary.mcs\" \"$(FPGA_TOP)_secondary.mcs\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.PRM_FILES [list \"$(FPGA_TOP)_primary.prm\" \"$(FPGA_TOP)_secondary.prm\"] [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ERASE 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CFG_PROGRAM 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.VERIFY 1 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.CHECKSUM 0 [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.ADDRESS_RANGE {use_file} [current_hw_cfgmem]" >> flash.tcl
+	echo "set_property PROGRAM.UNUSED_PIN_TERMINATION {pull-none} [current_hw_cfgmem]" >> flash.tcl
+	echo "create_hw_bitstream -hw_device [current_hw_device] [get_property PROGRAM.HW_CFGMEM_BITFILE [current_hw_device]]" >> flash.tcl
+	echo "program_hw_devices [current_hw_device]" >> flash.tcl
+	echo "refresh_hw_device [current_hw_device]" >> flash.tcl
+	echo "program_hw_cfgmem -hw_cfgmem [current_hw_cfgmem]" >> flash.tcl
+	echo "boot_hw_device [current_hw_device]" >> flash.tcl
+	echo "exit" >> flash.tcl
+	vivado -nojournal -nolog -mode batch -source flash.tcl
+

example/HTG9200/fpga_fmc_htg_6qsfp_25g/fpga_vu13p/config.tcl

@@ -0,0 +1,50 @@
+# Copyright (c) 2023 Alex Forencich
+#
+# Permission is hereby granted, free of charge, to any person obtaining a copy
+# of this software and associated documentation files (the "Software"), to deal
+# in the Software without restriction, including without limitation the rights
+# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+# copies of the Software, and to permit persons to whom the Software is
+# furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice shall be included in
+# all copies or substantial portions of the Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+# THE SOFTWARE.
+
+# Transceiver configuration
+set eth_xcvr_freerun_freq {125}
+set eth_xcvr_line_rate {25.78125}
+set eth_xcvr_sec_line_rate {0}
+set eth_xcvr_refclk_freq {161.1328125}
+set eth_xcvr_qpll_fracn [expr {int(fmod($eth_xcvr_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_sec_qpll_fracn [expr {int(fmod($eth_xcvr_sec_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_rx_eq_mode {DFE}
+
+set xcvr_config [dict create]
+
+dict set xcvr_config CONFIG.TX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.TX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.TX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.RX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.RX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_EQ_MODE $eth_xcvr_rx_eq_mode
+if {$eth_xcvr_sec_line_rate != 0} {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE true
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_FRACN_NUMERATOR $eth_xcvr_sec_qpll_fracn
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_LINE_RATE $eth_xcvr_sec_line_rate
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+} else {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE false
+}
+dict set xcvr_config CONFIG.FREERUN_FREQUENCY $eth_xcvr_freerun_freq
+
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_full]
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_channel]

example/HTG9200/fpga_fmc_htg_6qsfp_25g/fpga_vu9p/config.tcl

@@ -0,0 +1,50 @@
+# Copyright (c) 2023 Alex Forencich
+#
+# Permission is hereby granted, free of charge, to any person obtaining a copy
+# of this software and associated documentation files (the "Software"), to deal
+# in the Software without restriction, including without limitation the rights
+# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+# copies of the Software, and to permit persons to whom the Software is
+# furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice shall be included in
+# all copies or substantial portions of the Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+# THE SOFTWARE.
+
+# Transceiver configuration
+set eth_xcvr_freerun_freq {125}
+set eth_xcvr_line_rate {25.78125}
+set eth_xcvr_sec_line_rate {0}
+set eth_xcvr_refclk_freq {161.1328125}
+set eth_xcvr_qpll_fracn [expr {int(fmod($eth_xcvr_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_sec_qpll_fracn [expr {int(fmod($eth_xcvr_sec_line_rate*1000/2 / $eth_xcvr_refclk_freq, 1)*pow(2, 24))}]
+set eth_xcvr_rx_eq_mode {DFE}
+
+set xcvr_config [dict create]
+
+dict set xcvr_config CONFIG.TX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.TX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.TX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_LINE_RATE $eth_xcvr_line_rate
+dict set xcvr_config CONFIG.RX_QPLL_FRACN_NUMERATOR $eth_xcvr_qpll_fracn
+dict set xcvr_config CONFIG.RX_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+dict set xcvr_config CONFIG.RX_EQ_MODE $eth_xcvr_rx_eq_mode
+if {$eth_xcvr_sec_line_rate != 0} {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE true
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_FRACN_NUMERATOR $eth_xcvr_sec_qpll_fracn
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_LINE_RATE $eth_xcvr_sec_line_rate
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_REFCLK_FREQUENCY $eth_xcvr_refclk_freq
+} else {
+    dict set xcvr_config CONFIG.SECONDARY_QPLL_ENABLE false
+}
+dict set xcvr_config CONFIG.FREERUN_FREQUENCY $eth_xcvr_freerun_freq
+
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_full]
+set_property -dict $xcvr_config [get_ips eth_xcvr_gt_channel]