//****************************************************************************
// Product: "Blinky" example, EK-TM4C123GXL board, cooperative Vanilla kernel
// Last updated for version 5.5.0
// Last updated on 2015-09-23
//
// Q u a n t u m L e a P s
// ---------------------------
// innovating embedded systems
//
// Copyright (C) Quantum Leaps, LLC. All rights reserved.
//
// This program is open source software: you can redistribute it and/or
// modify it under the terms of the GNU General Public License as published
// by the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// Alternatively, this program may be distributed and modified under the
// terms of Quantum Leaps commercial licenses, which expressly supersede
// the GNU General Public License and are specifically designed for
// licensees interested in retaining the proprietary status of their code.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see .
//
// Contact information:
// https://state-machine.com
// mailto:info@state-machine.com
//****************************************************************************
#include "qpcpp.h"
#include "blinky.h"
#include "bsp.h"
#include "TM4C123GH6PM.h" // the device specific header (TI)
#include "rom.h" // the built-in ROM functions (TI)
#include "sysctl.h" // system control driver (TI)
#include "gpio.h" // GPIO driver (TI)
// add other drivers if necessary...
#ifdef Q_SPY
#error Simple Blinky Application does not provide Spy build configuration
#endif
//Q_DEFINE_THIS_FILE
// !!!!!!!!!!!!!!!!!!!!!!!!!!!!! CAUTION !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
// Assign a priority to EVERY ISR explicitly by calling NVIC_SetPriority().
// DO NOT LEAVE THE ISR PRIORITIES AT THE DEFAULT VALUE!
//
enum KernelUnawareISRs { // see NOTE00
// ...
MAX_KERNEL_UNAWARE_CMSIS_PRI // keep always last
};
// "kernel-unaware" interrupts can't overlap "kernel-aware" interrupts
Q_ASSERT_COMPILE(MAX_KERNEL_UNAWARE_CMSIS_PRI <= QF_AWARE_ISR_CMSIS_PRI);
enum KernelAwareISRs {
SYSTICK_PRIO = QF_AWARE_ISR_CMSIS_PRI, // see NOTE00
// ...
MAX_KERNEL_AWARE_CMSIS_PRI // keep always last
};
// "kernel-aware" interrupts should not overlap the PendSV priority
Q_ASSERT_COMPILE(MAX_KERNEL_AWARE_CMSIS_PRI <= (0xFF >>(8-__NVIC_PRIO_BITS)));
// Local-scope objects -------------------------------------------------------
#define LED_RED (1U << 1)
#define LED_GREEN (1U << 3)
#define LED_BLUE (1U << 2)
#define BTN_SW1 (1U << 4)
#define BTN_SW2 (1U << 0)
// ISRs used in this project =================================================
extern "C" {
//............................................................................
void SysTick_Handler(void); // prototype
void SysTick_Handler(void) {
QF::TICK_X(0U, (void *)0); // process time events for rate 0
}
} // extern "C"
// BSP functions =============================================================
void BSP_init(void) {
// NOTE: SystemInit() already called from the startup code
// but SystemCoreClock needs to be updated
//
SystemCoreClockUpdate();
// configure the FPU usage by choosing one of the options...
// Do NOT to use the automatic FPU state preservation and
// do NOT to use the FPU lazy stacking.
//
// NOTE:
// Use the following setting when FPU is used only by active objects
// and NOT in any ISR. This setting is very efficient, but if any ISRs
// start using the FPU, this can lead to corruption of the FPU registers.
//
FPU->FPCCR &= ~((1U << FPU_FPCCR_ASPEN_Pos) | (1U << FPU_FPCCR_LSPEN_Pos));
// enable clock for to the peripherals used by this application...
SYSCTL->RCGCGPIO |= (1U << 5); // enable Run mode for GPIOF
// configure the LEDs and push buttons
GPIOF->DIR |= (LED_RED | LED_GREEN | LED_BLUE); // set direction: output
GPIOF->DEN |= (LED_RED | LED_GREEN | LED_BLUE); // digital enable
GPIOF->DATA_Bits[LED_RED] = 0U; // turn the LED off
GPIOF->DATA_Bits[LED_GREEN] = 0U; // turn the LED off
GPIOF->DATA_Bits[LED_BLUE] = 0U; // turn the LED off
// configure the Buttons
GPIOF->DIR &= ~(BTN_SW1 | BTN_SW2); // set direction: input
ROM_GPIOPadConfigSet(GPIOF_BASE, (BTN_SW1 | BTN_SW2),
GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
}
//............................................................................
void BSP_ledOff(void) {
GPIOF->DATA_Bits[LED_GREEN] = 0U;
}
//............................................................................
void BSP_ledOn(void) {
// exercise the FPU with some floating point computations
float volatile x = 3.1415926F;
x = x + 2.7182818F;
GPIOF->DATA_Bits[LED_GREEN] = 0xFFU;
}
// QF callbacks ==============================================================
void QF::onStartup(void) {
// set up the SysTick timer to fire at BSP_TICKS_PER_SEC rate
SysTick_Config(SystemCoreClock / BSP_TICKS_PER_SEC);
// assing all priority bits for preemption-prio. and none to sub-prio.
NVIC_SetPriorityGrouping(0U);
// set priorities of ALL ISRs used in the system, see NOTE00
//
// !!!!!!!!!!!!!!!!!!!!!!!!!!! CAUTION !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
// Assign a priority to EVERY ISR explicitly by calling NVIC_SetPriority().
// DO NOT LEAVE THE ISR PRIORITIES AT THE DEFAULT VALUE!
//
NVIC_SetPriority(SysTick_IRQn, SYSTICK_PRIO);
// ...
// enable IRQs...
}
//............................................................................
void QF::onCleanup(void) {
}
//............................................................................
void QV::onIdle(void) { // CATION: called with interrupts DISABLED, NOTE01
// toggle LED2 on and then off, see NOTE01
GPIOF->DATA_Bits[LED_BLUE] = 0xFFU;
GPIOF->DATA_Bits[LED_BLUE] = 0x00U;
#ifdef NDEBUG
// Put the CPU and peripherals to the low-power mode.
// you might need to customize the clock management for your application,
// see the datasheet for your particular Cortex-M3 MCU.
//
QV_CPU_SLEEP(); // atomically go to sleep and enable interrupts
#else
QF_INT_ENABLE(); // just enable interrupts
#endif
}
//............................................................................
extern "C" void Q_onAssert(char const *module, int loc) {
//
// NOTE: add here your application-specific error handling
//
(void)module;
(void)loc;
QS_ASSERTION(module, loc, static_cast(10000U));
NVIC_SystemReset();
}
//****************************************************************************
// NOTE00:
// The QF_AWARE_ISR_CMSIS_PRI constant from the QF port specifies the highest
// ISR priority that is disabled by the QF framework. The value is suitable
// for the NVIC_SetPriority() CMSIS function.
//
// Only ISRs prioritized at or below the QF_AWARE_ISR_CMSIS_PRI level (i.e.,
// with the numerical values of priorities equal or higher than
// QF_AWARE_ISR_CMSIS_PRI) are allowed to call any QF services. These ISRs
// are "QF-aware".
//
// Conversely, any ISRs prioritized above the QF_AWARE_ISR_CMSIS_PRI priority
// level (i.e., with the numerical values of priorities less than
// QF_AWARE_ISR_CMSIS_PRI) are never disabled and are not aware of the kernel.
// Such "QF-unaware" ISRs cannot call any QF services. The only mechanism
// by which a "QF-unaware" ISR can communicate with the QF framework is by
// triggering a "QF-aware" ISR, which can post/publish events.
//
// NOTE01:
// The QV::onIdle() callback is called with interrupts disabled, because the
// determination of the idle condition might change by any interrupt posting
// an event. QV::onIdle() must internally enable interrupts, ideally
// atomically with putting the CPU to the power-saving mode.
//
// NOTE02:
// One of the LEDs is used to visualize the idle loop activity. The brightness
// of the LED is proportional to the frequency of invcations of the idle loop.
// Please note that the LED is toggled with interrupts locked, so no interrupt
// execution time contributes to the brightness of the User LED.
//